Bobcat loaders are important machines used in construction and landscaping projects to get the job done quickly. Sometimes, these machines can have problems. But don’t worry! Bobcats have a special computer system with error codes that tell us what’s wrong. By checking these error codes, we can figure out the issue and fix the Bobcat so it can work again!
Bobcat fault codes list
| Error Code | Description | Possible Causes | Solutions |
|---|---|---|---|
| 01-16 | Air filter not connected | Air filter not properly attached | Check and secure the air filter; replace if necessary |
| 01-17 | Clogged air filter | Dirty air filter blocking airflow | Clean or replace the clogged air filter |
| 02-16 | No hydraulic discharge filter connected | Missing or improperly installed hydraulic discharge filter | Install a new hydraulic discharge filter |
| 02-17 | Clogged hydraulic discharge filter | Hydraulic discharge filter clogged with contaminants | Clean or replace the clogged hydraulic discharge filter |
| 03-09 | Low battery voltage | Battery is low on charge or faulty | Charge or replace the battery if necessary |
| 03-10 | High battery voltage | Battery voltage too high | Disconnect and have the battery checked by a professional |
| 03-11 | Extremely high battery voltage | Dangerously high battery voltage | Disconnect and seek professional assistance immediately |
| 03-14 | Extremely low battery voltage | Battery almost depleted or faulty | Charge or replace the battery if needed |
| 03-22 | Battery voltage below maximum permissible | Battery voltage too low | Check battery health and charging system; replace if needed |
| 04-09 | Low oil pressure in the engine | Engine oil leak or low oil level | Check oil level and system; seek professional assistance |
| 04-14 | Extremely high engine oil pressure | Engine overheating or oil passages blocked | Stop engine, let it cool, and seek professional help |
| 04-15 | Engine oil pressure at emergency shutdown level | Critical engine oil pressure | Stop engine immediately; inspect oil system; professional help |
| 04-21 | Engine oil pressure above maximum permissible | Engine oil pressure too high | Stop engine, let it cool, and seek professional help |
| 04-22 | Engine oil pressure below maximum permissible | Engine oil pressure too low | Stop engine; check oil level and leaks; professional help |
| 05-09 | Low recharge pressure in hydraulic system | Hydraulic fluid leak or system component issue | Check fluid level and leaks; seek professional assistance |
| 05-14 | Extremely low recharge pressure in hydraulic system | Severe hydraulic system problem | Stop using machine; seek professional inspection and repair |
| 05-15 | Recharge pressure at engine emergency shutdown level | Critical hydraulic system pressure | Stop using machine; seek professional inspection and repair |
| 05-21 | Recharge pressure above maximum permissible | Hydraulic system pressure too high | Stop using machine; have professional adjust pressure |
| 05-22 | Recharge pressure below maximum permissible | Hydraulic system pressure too low | Have professional inspect and adjust hydraulic system |
| 06-10 | High engine speed | Engine running at a high speed | Adjust engine speed to a normal level |
| 06-11 | Extremely high engine speed | Engine running at a dangerously high speed | Immediately reduce engine speed to a safe level |
| 06-13 | No engine speed signal | Lack of signal indicating the engine speed | Check engine speed sensor; repair or replace if necessary |
| 06-15 | Engine speed at the emergency shutdown level | Engine speed reached a critical level | Stop the engine to avoid damage |
| 06-18 | Engine speed outside the permissible limits | Engine speed is not within safe operating limits | Adjust engine speed to fall within safe parameters |
| 07-10 | High oil temperature in the hydraulic system | Hydraulic system oil temperature is high | Check hydraulic system cooling; resolve any issues |
| 07-11 | Extremely high oil temperature in hydraulic system | Hydraulic system oil temperature dangerously high | Stop using the machine; seek professional help immediately |
| 07-15 | Oil temperature in hydraulic system at emergency shutdown level | Hydraulic system oil temperature at a critical point | Stop the machine immediately to prevent further damage |
| 07-21 | Oil temperature in hydraulic system above maximum permissible | Hydraulic system oil temperature too high | Stop using the machine; have professional check and fix issue |
| 07-22 | Oil temperature in hydraulic system below maximum permissible | Hydraulic system oil temperature too low | Have professional inspect and address hydraulic system issue |
| 08-10 | High engine coolant temperature | Engine coolant temperature is high | Check cooling system; resolve any issues |
| 08-11 | Extremely high engine coolant temperature | Engine coolant temperature dangerously high | Stop the engine; seek immediate professional assistance |
| 08-15 | Engine coolant temperature at emergency shutdown level | Engine coolant temperature critical | Stop the engine immediately to prevent further damage |
| 08-21 | Engine coolant temperature above maximum permissible | Engine coolant temperature too high | Stop using the machine; have professional check and fix issue |
| 08-22 | Engine coolant temperature below maximum permissible | Engine coolant temperature too low | Have professional inspect and address engine coolant issue |
| 09-09 | Low fuel level | Low fuel level in the tank | Refuel the machine to an adequate level |
| 09-21 | Fuel level above maximum permissible | Fuel level is higher than the safe limit | Check fuel system; resolve any issues |
| 09-22 | Fuel level below maximum permissible | Fuel level is lower than the safe limit | Refuel the machine to an adequate level |
| 11-05 | Safety frame sensor closed to the battery | Safety frame sensor detecting a closed circuit | Check sensor connection and wiring; repair or replace as needed |
| 11-06 | Security frame sensor closed to mass | Security frame sensor detecting a closed circuit | Check sensor connection and wiring; repair or replace as needed |
| 12-21 | Signal PWM Controller front additional hydraulics at upper limit of the range | Hydraulic system signal at upper limit | Check front additional hydraulics system; adjust if necessary |
| 12-22 | Signal PWM Controller front additional hydraulics at lower limit of the range | Hydraulic system signal at lower limit | Check front additional hydraulics system; adjust if necessary |
| 12-23 | Signal PWM Controller front additional hydraulics not in neutral position | Hydraulic system signal not in neutral | Check front additional hydraulics system; resolve any issues |
| 13-05 | Retaining solenoid of fuel cutoff closed on battery | Issue with fuel cutoff solenoid circuit | Check and repair the fuel cutoff solenoid circuit |
| 13-06 | Retaining solenoid of fuel cutoff closed to mass | Issue with fuel cutoff solenoid circuit | Check and repair the fuel cutoff solenoid circuit |
| 13-07 | Circuit Break solenoid cutoff fuel | Issue with fuel cutoff solenoid circuit | Check and repair the fuel cutoff solenoid circuit |
| 14-02 | Motorcyclist the fuel cutoff solenoid, erroneous switching on | Incorrect activation of fuel cutoff solenoid | Check and repair the fuel cutoff solenoid |
| 14-03 | Motorcyclist the fuel cutoff solenoid, erroneous shutdown | Incorrect deactivation of fuel cutoff solenoid | Check and repair the fuel cutoff solenoid |
| 15-02 | Motorcyclist solenoid lock thrust, erroneous inclusion | Incorrect activation of lock thrust solenoid | Check and repair the lock thrust solenoid |
| 15-03 | Motorcyclist solenoid lock thrust, erroneous shutdown | Incorrect deactivation of lock thrust solenoid | Check and repair the lock thrust solenoid |
| 16-05 | The holding solenoid lock is closed on the battery | Issue with the holding solenoid circuit | Check and repair the holding solenoid circuit |
| 16-06 | The holding solenoid of the thrust lock is closed to the mass | Issue with the holding solenoid circuit | Check and repair the holding solenoid circuit |
| 16-07 | Tearing chain restraint solenoid lock thrust | Issue with the holding solenoid circuit | Check and repair the holding solenoid circuit |
| 17-05 | The hydraulic valve solenoid is closed to the battery | Issue with hydraulic valve solenoid circuit | Check and repair the hydraulic valve solenoid circuit |
| 17-06 | The hydraulic valve solenoid is closed to the mass | Issue with hydraulic valve solenoid circuit | Check and repair the hydraulic valve solenoid circuit |
| 17-07 | Rupture of the solenoid circuit of the hydraulic shutoff valve | Issue with hydraulic valve solenoid circuit | Check and repair the hydraulic valve solenoid circuit |
| 18-05 | The spool solenoid is closed on the battery | Issue with the spool solenoid circuit | Check and repair the spool solenoid circuit |
| 18-06 | The spool solenoid is closed to the mass | Issue with the spool solenoid circuit | Check and repair the spool solenoid circuit |
| 18-07 | Spool solenoid circuit break | Issue with the spool solenoid circuit | Check and repair the spool solenoid circuit |
| 19-02 | Bucket positioning solenoid, erroneous switching on | Incorrect activation of bucket positioning solenoid | Check and repair the bucket positioning solenoid |
| 19-03 | Bucket positioning solenoid, erroneous shutdown | Incorrect deactivation of bucket positioning solenoid | Check and repair the bucket positioning solenoid |
| 20-02 | Speed switching solenoid, erroneous switching on | Incorrect activation of speed switching solenoid | Check and repair the speed switching solenoid |
| 20-03 | Speed switch solenoid, erroneous shutdown | Incorrect deactivation of speed switching solenoid | Check and repair the speed switching solenoid |
| 21-02 | Glow plugs, erroneous inclusion | Incorrect activation of glow plugs | Check and repair the glow plugs |
| 21-03 | Glow plugs, erroneous shutdown | Incorrect deactivation of glow plugs | Check and repair the glow plugs |
| 22-02 | Starter, erroneous inclusion | Incorrect activation of the starter | Check and repair the starter circuit |
| 22-03 | Starter, erroneous shutdown | Incorrect deactivation of the starter | Check and repair the starter circuit |
| 23-02 | Rear base solenoid, erroneous switching on | Incorrect activation of rear base solenoid | Check and repair the rear base solenoid circuit |
| 23-03 | Rear base solenoid, erroneous shutdown | Incorrect deactivation of rear base solenoid | Check and repair the rear base solenoid circuit |
| 24-02 | Rear Pull Solenoid, erroneous switching on | Incorrect activation of rear pull solenoid | Check and repair the rear pull solenoid circuit |
| 24-03 | Rear Pull Solenoid, erroneous shutdown | Incorrect deactivation of rear pull solenoid | Check and repair the rear pull solenoid circuit |
| 25-02 | Rear auxiliary proportional solenoid, erroneous inclusion | Incorrect activation of rear auxiliary proportional solenoid | Check and repair the rear auxiliary proportional solenoid circuit |
| 25-03 | Rear auxiliary proportional solenoid, erroneous shutdown | Incorrect deactivation of rear auxiliary proportional solenoid | Check and repair the rear auxiliary proportional solenoid circuit |
| 26-02 | Erroneous inclusion of the front base solenoid | Incorrect activation of front base solenoid | Check and repair the front base solenoid circuit |
| 26-03 | Erroneous shutdown of the front base solenoid | Incorrect deactivation of front base solenoid | Check and repair the front base solenoid circuit |
| 27-02 | Erroneous inclusion of the front Stock Solenoid | Incorrect activation of front stock solenoid | Check and repair the front stock solenoid circuit |
| 27-03 | Erroneous shutdown of the front Stock Solenoid | Incorrect deactivation of front stock solenoid | Check and repair the front stock solenoid circuit |
| 28-02 | Erroneous inclusion of solenoid Divertera | Incorrect activation of diverter solenoid | Check and repair the diverter solenoid circuit |
| 28-03 | Incorrect solenoid shutdown Divertera | Incorrect deactivation of diverter solenoid | Check and repair the diverter solenoid circuit |
| 29-02 | Large feed solenoid, erroneous switching on | Incorrect activation of large feed solenoid | Check and repair the large feed solenoid circuit |
| 29-03 | Large feed solenoid, erroneous shutdown | Incorrect deactivation of large feed solenoid | Check and repair the large feed solenoid circuit |
| 30-28 | Controller memory failure | Issue with the loader’s controller memory | Professional diagnosis and repair of the controller memory |
| 31-28 | Recovery mode failure | Issue with the loader’s recovery mode | Professional diagnosis and repair of the recovery mode |
| 32-04 | Advanced Management (ACS) not reported to the controller Bobcat | Issue with the loader’s Advanced Management (ACS) system | Professional diagnosis and repair of the Advanced Management (ACS) system |
| 32-23 | ACS Advanced Management Not calibrated | Advanced Management (ACS) system not calibrated | Calibration of the Advanced Management (ACS) system |
| 32-31 | Failure of the actuating mechanism of inclination | Issue with the loader’s actuating mechanism of inclination | Check and repair the actuating mechanism of inclination |
| 32-32 | Malfunction of the electrical wiring of the actuating mechanism of inclination | Issue with electrical wiring of the actuating mechanism of inclination | Check and repair the electrical wiring of the actuating mechanism of inclination |
| 32-33 | Failure of the electrical wiring of the bucket tilting handle | Issue with electrical wiring of the bucket tilting handle | Check and repair the electrical wiring of the bucket tilting handle |
| 32-34 | Executive tilting mechanism not in neutral position | Actuating mechanism of tilting not in the neutral position | Check and adjust the actuating mechanism of tilting |
| 32-35 | Handle/Bucket tilt pedal not in neutral position | Handle/Bucket tilt pedal not in the neutral position | Check and adjust the handle/bucket tilt pedal |
| 32-36 | Failure of the actuating mechanism of lifting | Issue with the loader’s actuating mechanism of lifting | Check and repair the actuating mechanism of lifting |
| 32-37 | Malfunction of electrical wiring of the actuating mechanism of lifting | Issue with electrical wiring of the actuating mechanism of lifting | Check and repair the electrical wiring of the actuating mechanism of lifting |
| 32-38 | Failure of the electrical wiring of the boom handle | Issue with electrical wiring of the boom handle | Check and repair the electrical wiring of the boom handle |
| 32-39 | Executive lifting mechanism not in neutral position | Actuating mechanism of lifting not in the neutral position | Check and adjust the actuating mechanism of lifting |
| 32-40 | Arm/Boom lift pedal not in neutral position | Arm/Boom lift pedal not in the neutral position | Check and adjust the arm/boom lift pedal |
| 32-41 | No connection | No connection with the specified component | Check and establish the connection with the specified component |
| 32-49 | Executive lifting mechanism closed to mass | Actuating mechanism of lifting closed to mass | Check and repair the actuating mechanism of lifting |
| 32-50 | The executive tilting mechanism is closed to mass | Actuating mechanism of tilting closed to mass | Check and repair the actuating mechanism of tilting |
| 32-51 | Actuator lifting mechanism closed on the battery | Actuating mechanism of lifting closed on the battery | Check and repair the actuating mechanism of lifting |
| 32-52 | The actuator tilting mechanism is closed to the battery | Actuating mechanism of tilting closed on the battery | Check and repair the actuating mechanism of tilting |
| 32-53 | Handle/Boom lift pedal closed to mass | Handle/Boom lift pedal closed to mass | Check and repair the handle/boom lift pedal |
| 32-54 | Handle/Bucket tilt pedal closed to mass | Handle/Bucket tilt pedal closed to mass | Check and repair the handle/bucket tilt pedal |
| 32-54 | Handle/Bucket tilt pedal closed to mass | Issue with the handle/bucket tilt pedal circuit | Check and repair the handle/bucket tilt pedal circuit |
| 32-55 | Arm/Boom lift pedal closed on battery | Issue with the arm/boom lift pedal circuit | Check and repair the arm/boom lift pedal circuit |
| 32-56 | The handle/bucket tilt pedal is closed to the battery | Issue with the handle/bucket tilt pedal circuit | Check and repair the handle/bucket tilt pedal circuit |
| 32-57 | Reduced performance of the lifting actuation mechanism | Issue with the lifting actuation mechanism | Check and repair the lifting actuation mechanism circuit |
| 32-58 | Reduced performance of the executive tilt mechanism | Issue with the executive tilt mechanism | Check and repair the executive tilt mechanism circuit |
| 32-59 | Wrong direction of the actuating mechanism of lifting | Issue with the actuating mechanism of lifting | Check and repair the actuating mechanism of lifting |
| 32-60 | Wrong direction of the executive tilt mechanism | Issue with the executive tilt mechanism | Check and repair the executive tilt mechanism circuit |
| 32-61 | The lock of arms is closed to mass | Issue with the lock of arms circuit | Check and repair the lock of arms circuit |
| 32-62 | The lock of Arms is closed on the battery | Issue with the lock of arms circuit | Check and repair the lock of arms circuit |
| 32-63 | The chain of locking pedals is closed to the mass | Issue with the chain of locking pedals circuit | Check and repair the chain of locking pedals circuit |
| 32-64 | The chain of locking pedals is closed to the battery | Issue with the chain of locking pedals circuit | Check and repair the chain of locking pedals circuit |
| 32-65 | Sensor supply voltage outside the permissible limits | Issue with the sensor supply voltage | Check and address the sensor supply voltage |
| 32-66 | Battery voltage out of the allowable limits | Issue with the loader’s battery voltage | Check and address the loader’s battery voltage |
| 32-67 | Switched during Operation | Issue with the control switches during operation | Check and repair any faulty control switches |
| 32-68 | Boom Boom ARM Information error | Issue with the boom arm information | Check and address the boom arm information |
| 32-69 | The switch of control modes has switched during operation | Issue with the control mode switch circuit | Check and repair the control mode switch circuit |
| 32-70 | The chain of the right handle of motion is closed to mass | Issue with the chain of the right handle of motion circuit | Check and repair the chain of the right handle of motion circuit |
| 32-71 | Circuit of the right handle of movement is closed on the battery | Issue with the circuit of the right handle of movement | Check and repair the circuit of the right handle of movement |
| 33-23 | Main controller (Controller Bobcat) Not programmed | Main controller not programmed | Program the main controller |
| 34-04 | The keypad with a button run is not reported to the controller Bobcat | Issue with the keypad circuit | Check and repair the keypad circuit |
| 35-02 | Speed fan switch, erroneous switching on | Incorrect activation of the fan speed switch | Check and repair the fan speed switch circuit |
| 35-03 | Speed fan switch, erroneous shutdown | Incorrect deactivation of the fan speed switch | Check and repair the fan speed switch circuit |
| 36-48 | Multiple ACD controllers are connected | Multiple ACD controllers connected | Check and address multiple ACD controllers |
| 37-02 | Speed additional speed switch, erroneous switching on | Incorrect activation of the additional speed switch | Check and repair the additional speed switch circuit |
| 37-03 | Speed additional speed switch, erroneous shutdown | Incorrect deactivation of the additional speed switch | Check and repair the additional speed switch circuit |
| 38-04 | No connection to Joystick controller | No connection with the joystick controller | Check and establish the connection with the joystick controller |
| 38-05 | The x-axis of the left joystick is not in a neutral position | Left joystick’s x-axis not in neutral position | Check and adjust the left joystick’s x-axis |
| 38-06 | The X-axis of the right joystick is not in a neutral position | Right joystick’s X-axis not in neutral position | Check and adjust the right joystick’s X-axis |
| 38-07 | The Y-axis of the left joystick is not in a neutral position | Left joystick’s Y-axis not in neutral position | Check and adjust the left joystick’s Y-axis |
| 38-08 | The Y-axis of the right joystick is not in a neutral position | Right joystick’s Y-axis not in neutral position | Check and adjust the right joystick’s Y-axis |
| 38-09 | Control mode switch-circuit to the battery or to the mass | Issue with control mode switch circuit | Check and repair the control mode switch circuit |
| 38-11 | Executive lifting mechanism not in neutral position | Actuating mechanism of lifting not in neutral position | Check and adjust the actuating mechanism of lifting |
| 38-12 | Executive tilting mechanism not in neutral position | Actuating mechanism of tilting not in neutral position | Check and adjust the actuating mechanism of tilting |
| 38-13 | Failure of the actuating mechanism of lifting | Issue with the actuating mechanism of lifting | Check and repair the actuating mechanism of lifting |
| 38-14 | Failure of the actuating mechanism of inclination | Issue with the actuating mechanism of inclination | Check and repair the actuating mechanism of inclination |
| 38-15 | Right Wheel speed control failure | Issue with the right wheel speed control | Check and repair the right wheel speed control circuit |
| 38-16 | Faulty wiring for the speed of the left wheel | Issue with the left wheel speed control | Check and repair the left wheel speed control circuit |
| 38-17 | Reduced performance of the executive tilt mechanism | Issue with the executive tilt mechanism | Check and repair the executive tilt mechanism circuit |
| 38-18 | Reduced performance of the lifting actuation mechanism | Issue with the lifting actuation mechanism | Check and repair the lifting actuation mechanism circuit |
| 38-19 | The X-axis of the left joystick, behind the upper bound of the range | Left joystick’s X-axis out of range | Check and adjust the left joystick’s X-axis |
| 38-20 | X-axis of the right joystick, beyond the lower bound of the range | Right joystick’s X-axis out of range | Check and adjust the right joystick’s X-axis |
| 38-21 | The Y-axis of the left joystick, behind the upper bound of the range | Left joystick’s Y-axis out of range | Check and adjust the left joystick’s Y-axis |
| 38-22 | The Y-axis of the right joystick, behind the upper bound of the range | Right joystick’s Y-axis out of range | Check and adjust the right joystick’s Y-axis |
| 38-23 | Signal of the front right control sensor outside the upper boundary of the range | Issue with the front right control sensor | Check and calibrate the front right control sensor |
| 38-24 | Signal of the front left control sensor at the upper limit of the range | Issue with the front left control sensor | Check and calibrate the front left control sensor |
| 38-25 | Signal of the rear right control sensor at the upper limit of the range | Issue with the rear right control sensor | Check and calibrate the rear right control sensor |
| 38-26 | Signal of the rear left control sensor at the upper limit of the range | Issue with the rear left control sensor | Check and calibrate the rear left control sensor |
| 38-27 | Signal of the actuating mechanism of lifting at the upper boundary of the range | Issue with the actuating mechanism of lifting | Check and calibrate the actuating mechanism of lifting |
| 38-28 | Signal of the executive mechanism of inclination at the upper boundary of the range | Issue with the executive mechanism of inclination | Check and calibrate the executive mechanism of inclination |
| 38-29 | X-axis of the left joystick, behind the lower bound of the range | Issue with the left joystick’s X-axis | Check and calibrate the left joystick’s X-axis |
| 38-30 | X-axis of the right joystick, beyond the lower bound of the range | Issue with the right joystick’s X-axis | Check and calibrate the right joystick’s X-axis |
| 38-31 | Y-axis of the left joystick, beyond the lower bound of the range | Issue with the left joystick’s Y-axis | Check and calibrate the left joystick’s Y-axis |
| 38-32 | Y-axis of the right joystick, beyond the lower bound of the range | Issue with the right joystick’s Y-axis | Check and calibrate the right joystick’s Y-axis |
| 38-33 | Signal of the front right control sensor at the lower limit of the range | Issue with the front right control sensor | Check and calibrate the front right control sensor |
| 38-34 | Signal of the front left control sensor at the lower limit of the range | Issue with the front left control sensor | Check and calibrate the front left control sensor |
| 38-35 | Signal of the rear right control sensor at the lower limit of the range | Issue with the rear right control sensor | Check and calibrate the rear right control sensor |
| 38-36 | Signal of the rear left control sensor at the lower limit of the range | Issue with the rear left control sensor | Check and calibrate the rear left control sensor |
| 38-37 | Power supply “1” 5-volt sensor, behind the lower boundary of the range | Issue with the power supply “1” 5-volt sensor | Check and address the power supply “1” 5-volt sensor |
| 38-38 | Power supply “2” 5-volt sensor, behind the lower boundary of the range | Issue with the power supply “2” 5-volt sensor | Check and address the power supply “2” 5-volt sensor |
| 38-39 | Executive lifting mechanism closed to mass/beyond the lower boundary of the range | Issue with the executive lifting mechanism | Check and repair the executive lifting mechanism circuit |
| 38-40 | The executive tilt mechanism is closed to the mass/signal at the lower limit of the range | Issue with the executive tilt mechanism | Check and repair the executive tilt mechanism circuit |
| 38-41 | Wrong direction of the executive tilt mechanism | Issue with the executive tilt mechanism | Check and repair the executive tilt mechanism circuit |
| 38-42 | Wrong direction of the actuating mechanism of lifting | Issue with the actuating mechanism of lifting | Check and repair the actuating mechanism of lifting |
| 38-43 | The solenoid of the left front drive, erroneous switching on | Issue with the solenoid of the left front drive | Check and repair the solenoid of the left front drive |
| 38-44 | Solenoid of left reversible drive, erroneous switching on | Issue with the solenoid of the left reversible drive | Check and repair the solenoid of the left reversible drive |
| 38-45 | Right front drive solenoid, erroneous switching on | Issue with the right front drive solenoid | Check and repair the right front drive solenoid |
| 38-46 | Right reverse actuator solenoid, erroneous switching on | Issue with the right reverse actuator solenoid | Check and repair the right reverse actuator solenoid |
| 38-47 | Front right control solenoid, erroneous switching on | Issue with the front right control solenoid | Check and repair the front right control solenoid |
| 38-48 | Front left solenoid control, erroneous switching on | Issue with the front left solenoid control | Check and repair the front left solenoid control |
| 38-49 | Rear right control solenoid, erroneous switching on | Issue with the rear right control solenoid | Check and repair the rear right control solenoid |
| 38-50 | Rear left solenoid control, erroneous switching on | Issue with the rear left solenoid control | Check and repair the rear left solenoid control |
| 38-51 | Control system pressure solenoid, erroneous switching on | Issue with the control system pressure solenoid | Check and repair the control system pressure solenoid |
| 38-52 | Reversing signal, erroneous switching on | Issue with the reversing signal | Check and repair the reversing signal circuit |
| 38-53 | Left Front drive solenoid, erroneous shutdown | Issue with the left front drive solenoid | Check and repair the left front drive solenoid |
| 38-54 | Solenoid of left reversible drive, erroneous shutdown | Issue with the solenoid of the left reversible drive | Check and repair the solenoid of the left reversible drive |
| 38-55 | Right front drive solenoid, erroneous shutdown | Issue with the right front drive solenoid | Check and repair the right front drive solenoid |
| 38-56 | Right reverse actuator solenoid, erroneous shutdown | Issue with the right reverse actuator solenoid | Check and repair the right reverse actuator solenoid |
| 38-57 | Front right extension control solenoid, erroneous shutdown | Issue with the front right extension control solenoid | Check and repair the front right extension control solenoid |
| 38-58 | Front right retraction control solenoid, erroneous shutdown | Issue with the front right retraction control solenoid | Check and repair the front right retraction control solenoid |
| 38-59 | Front left solenoid of extension control, erroneous shutdown | Issue with the front left solenoid of extension control | Check and repair the front left solenoid of extension control |
| 38-60 | Front left solenoid control retraction, erroneous shutdown | Issue with the front left solenoid control retraction | Check and repair the front left solenoid control retraction |
| 38-61 | Rear right extension control solenoid, erroneous shutdown | Issue with the rear right extension control solenoid | Check and repair the rear right extension control solenoid |
| 38-62 | Rear right retraction control solenoid, erroneous shutdown | Issue with the rear right retraction control solenoid | Check and repair the rear right retraction control solenoid |
| 38-63 | Rear left solenoid control, erroneous shutdown | Issue with the rear left solenoid control | Check and repair the rear left solenoid control |
| 38-64 | Rear left solenoid control retraction, erroneous shutdown | Issue with the rear left solenoid control retraction | Check and repair the rear left solenoid control retraction |
| 38-65 | Control system pressure solenoid, erroneous shutdown | Issue with the control system pressure solenoid | Check and repair the control system pressure solenoid |
| 38-66 | Reversing signal, erroneous shutdown | Issue with the reversing signal | Check and repair the reversing signal circuit |
| 38-67 | No messages from controller Bobcat | Communication issue between the Bobcat controller and components | Check the communication system and connections between the controller and components |
| 38-68 | Wheel setting angles (alignment) not calibrated | Wheel angle calibration error | Calibrate the wheel setting angles (alignment) |
| 38-69 | Actuating mechanisms of lifting and tilting are not calibrated | Actuating mechanisms calibration error | Calibrate the actuating mechanisms of lifting and tilting |
| 38-70 | Power off | The machine has been powered off | Check the machine’s power supply and restart if necessary |
| 38-71 | Battery voltage outside the permissible limits | Issue with the loader’s battery voltage | Check and correct the battery voltage to be within permissible limits |
| 38-72 | Drive Pump Not calibrated | Issue with the calibration of the drive pump | Calibrate the drive pump to ensure accurate operation |
| 38-73 | Control/Motion mode switch is switched on during operation | Issue with the control/motion mode switch | Avoid switching the control/motion mode during operation |
| 38-74 | Speed of the uncontrolled right wheel, erroneous switching on | Issue with the uncontrolled right wheel’s speed | Check and repair the speed sensor or wiring for the right wheel |
| 38-75 | Speed of uncontrolled left wheel, erroneous switching on | Issue with the uncontrolled left wheel’s speed | Check and repair the speed sensor or wiring for the left wheel |
| 38-76 | Control system pressure solenoid-insufficient current | Issue with the control system pressure solenoid | Check and ensure sufficient current flow to the control system pressure solenoid |
| 38-77 | Front right extension control solenoid-insufficient current | Issue with the front right extension control solenoid | Check and ensure sufficient current flow to the front right extension control solenoid |
| 38-78 | Front right retraction control solenoid-insufficient current | Issue with the front right retraction control solenoid | Check and ensure sufficient current flow to the front right retraction control solenoid |
| 38-79 | Forward left solenoid of extension control-insufficient current | Issue with the front left extension control solenoid | Check and ensure sufficient current flow to the front left extension control solenoid |
| 38-80 | Front left solenoid control retraction-insufficient current | Issue with the front left control retraction solenoid | Check and ensure sufficient current flow to the front left control retraction solenoid |
| 38-81 | Rear right extension control solenoid-insufficient current | Issue with the rear right extension control solenoid | Check and ensure sufficient current flow to the rear right extension control solenoid |
| 38-82 | Rear right retraction control solenoid-insufficient current | Issue with the rear right retraction control solenoid | Check and ensure sufficient current flow to the rear right retraction control solenoid |
| 38-83 | Rear left solenoid control-insufficient current | Issue with the rear left control solenoid | Check and ensure sufficient current flow to the rear left control solenoid |
| 38-84 | Rear left solenoid control retraction-insufficient current | Issue with the rear left control retraction solenoid | Check and ensure sufficient current flow to the rear left control retraction solenoid |
| 38-85 | Power supply “1” 5-volt sensor outside the upper boundary of the range | Issue with the power supply “1” 5-volt sensor | Check and address the power supply “1” 5-volt sensor if outside the upper boundary of the range |
| 38-86 | Power supply “2” 5-volt sensor outside the upper boundary of the range | Issue with the power supply “2” 5-volt sensor | Check and address the power supply “2” 5-volt sensor if outside the upper boundary of the range |
| 38-87 | Right front wheel lock (mechanical malfunction control) | Issue with the right front wheel lock | Check and repair the mechanical locking mechanism for the right front wheel |
| 38-88 | Locking of the Left front wheel (mechanical malfunction control) | Issue with the left front wheel lock | Check and repair the mechanical locking mechanism for the left front wheel |
| 38-89 | Right rear wheel lock (mechanical malfunction control) | Issue with the right rear wheel lock | Check and repair the mechanical locking mechanism for the right rear wheel |
| 38-90 | Rear left control error | Issue with the rear left control | Check and repair the rear left control |
| 38-91 | There are no pulses of the right wheel speed sensor | Issue with the right wheel speed sensor | Check and repair the right wheel speed sensor |
| 38-92 | There are no pulses of the left wheel speed sensor | Issue with the left wheel speed sensor | Check and repair the left wheel speed sensor |
| 38-93 | Right wheel speed sensor does not respond | Issue with the right wheel speed sensor | Check and ensure proper connection of the right wheel speed sensor |
| 38-94 | The left wheel speed sensor does not respond | Issue with the left wheel speed sensor | Check and ensure proper connection of the left wheel speed sensor |
| 38-98 | Controller in the drive calibration mode | Issue with the controller in the drive calibration mode | Check the controller and exit the drive calibration mode if not required |
| 38-99 | Controller in wheel position calibration mode | Issue with the controller in wheel position calibration mode | Check the controller and exit the wheel position calibration mode if not required |
| 45-03 | Right turn pointer, erroneous shutdown | Issue with the right turn pointer | Check and repair the right turn pointer |
| 46-02 | Left turn pointer, erroneous inclusion | Issue with the left turn pointer | Check and repair the left turn pointer |
| 46-03 | Left turn pointer, erroneous shutdown | Issue with the left turn pointer | Check and repair the left turn pointer |
| 47-21 | Power supply of 8-volt sensor at the upper limit of the range | Issue with the power supply of the 8-volt sensor | Check and address the power supply of the 8-volt sensor if at the upper limit of the range |
| 47-22 | Power supply of 8-volt sensor, behind the lower boundary of the range | Issue with the power supply of the 8-volt sensor | Check and address the power supply of the 8-volt sensor if behind the lower boundary of the range |
| 48-02 | Front light relays, erroneous switching on | Issue with the front light relays | Check and repair the front light relays |
| 48-03 | Front light relay, erroneous shutdown | Issue with the front light relay | Check and repair the front light relay |
| 49-02 | Rear light relay, erroneous switching on | Issue with the rear light relay | Check and repair the rear light relay |
| 49-03 | Rear light relay, erroneous shutdown | Issue with the rear light relay | Check and repair the rear light relay |
| 60-21 | Signal of the control lever of the back additional Hydraulics at the top of the range | Issue with the control lever of the back additional hydraulics | Check and repair the control lever of the back additional hydraulics if at the top of the range |
| 60-22 | Signal of the control lever of the back additional Hydraulics at the lower limit of the range | Issue with the control lever of the back additional hydraulics | Check and repair the control lever of the back additional hydraulics if at the lower limit of the range |
| 60-23 | Control lever of the back additional hydraulics not returned to the neutral position | Issue with the control lever of the back additional hydraulics | Check and repair the control lever of the back additional hydraulics if not returned to the neutral position |
| 64-02 | Failure to turn on the power relay | Issue with the power relay | Check and repair the power relay |
| 64-03 | Erroneous shutdown of the power relay | Issue with the power relay | Check and repair the power relay |
| 74-72 | Controller boot code failed Bobcat | Issue with the controller boot code | Check and repair the controller boot code |
| 74-73 | Left panel, receiving device error | Issue with the left panel receiving device | Check and repair the left panel receiving device |
| 80-02 | ACD, Exit “A”, erroneous switching on | Issue with ACD Exit “A” | Check and repair ACD Exit “A” |
| 80-03 | ACD, Exit “A”, erroneous shutdown | Issue with ACD Exit “A” | Check and repair ACD Exit “A” |
| 81-02 | ACD, Output “B”, erroneous switching on | Issue with ACD Output “B” | Check and repair ACD Output “B” |
| 81-03 | ACD, Exit “B”, erroneous shutdown | Issue with ACD Exit “B” | Check and repair ACD Exit “B” |
| 82-02 | ACD, Exit “C”, erroneous inclusion | Issue with ACD Exit “C” | Check and repair ACD Exit “C” |
| 82-03 | ACD, Exit “C”, erroneous shutdown | Issue with ACD Exit “C” | Check and repair ACD Exit “C” |
| 83-02 | ACD, Exit “D”, erroneous switching on | Issue with ACD Exit “D” | Check and repair ACD Exit “D” |
| 83-03 | ACD, Exit “D”, erroneous shutdown | Issue with ACD Exit “D” | Check and repair ACD Exit “D” |
| 84-02 | ACD, Output “E”, erroneous switching on | Issue with ACD Output “E” | Check and repair ACD Output “E” |
| 84-03 | ACD, Exit “E”, erroneous shutdown | Issue with ACD Exit “E” | Check and repair ACD Exit “E” |
| 90-02 | Service exit “C”, erroneous switching on | Issue with Service Exit “C” | Check and repair Service Exit “C” |
| 90-03 | Service exit “C”, erroneous shutdown | Issue with Service Exit “C” | Check and repair Service |
| 91-02 | Service exit “D”, erroneous switching on | Issue with Service Exit “D” | Check and repair Service Exit “D” |
| 91-03 | Service exit “D”, erroneous shutdown | Issue with Service Exit “D” | Check and repair Service Exit “D” |
| 92-02 | Service exit “E”, erroneous inclusion | Issue with Service Exit “E” | Check and repair Service Exit “E” |
| 92-03 | Service Output “E”, erroneous shutdown | Issue with Service Output “E” | Check and repair Service Output “E” |
| 93-02 | Service exit “F”, erroneous switching on | Issue with Service Exit “F” | Check and repair Service Exit “F” |
| 93-03 | Service exit “F”, erroneous shutdown | Issue with Service Exit “F” | Check and repair Service Exit “F” |
Bobcat Fault Code List by Product
| Fault Code | Product | Description |
|---|---|---|
| 03-01 | ECU Bobcat Engine V1 | EGR Temperature Sensor – Fault |
| 04-01 | ECU Bobcat Engine V1 | EGR Temperature Sensor – Fault |
| 3252-00 | ECU Bobcat Engine V1 | Exhaust Temperature – High |
| 03-01 | ECU Bobcat Engine V1 | Sensor Supply Voltage Fault |
| 04-01 | ECU Bobcat Engine V1 | Sensor Supply Voltage Fault |
| A0321 | Telehandler | Battery Voltage OOR High |
| A0322 | Telehandler | Battery Voltage OOR Low |
| A0618 | Attachments | Wheel Speed Out of Range |
| A0702 | Telehandler | Left interlocking sensor Short to Battery |
| A0703 | Telehandler | Left interlocking sensor Short to Ground or Open circuit |
| A0802 | Telehandler | Right interlocking sensor Short to Battery |
| A0803 | Telehandler | Right interlocking sensor Short to Ground or Open circuit |
| A0921 | Telehandler | Overload Signal 1 Out Of Range High |
| A0922 | Telehandler | Overload Signal 1 Out Of Range Low |
| A1021 | Telehandler | Overload Signal 2 Out Of Range High |
| A1022 | Telehandler | Overload Signal 2 Out Of Range Low |
| A1144 | Telehandler | Overload signals disagrees |
| A1198 | Telehandler | Overload calibration performed |
| A1199 | Telehandler | Overload calibration required |
| A1221 | Telehandler | Tilt inclinometer innput Out of range High |
| A1222 | Telehandler | Tilt inclinometer innput Out of range Low |
| A1298 | Telehandler | Tilt inclinometer calibration performed |
| A1299 | Telehandler | Tilt inclinometer calibration required |
| A3623 | Telehandler | Programming or constant data invalid |
| A3623 | Attachments | ACD Not Programmed |
| A4621 | Attachments | 5 Volt Sensor Supply Out of Range High |
| A4621 | M-Series Loader | 5V Sensor Supply Out of Range High |
| A4622 | M-Series Loader | 5V Sensor Supply Out of Range Low |
| A4622 | Attachments | 5 Volt Sensor Supply Out of Range Low |
| A4721 | Attachments | 8 Volt Sensor Supply Out of Range High |
| A4721 | M-Series Loader | 8V Sensor Supply Out of Range High |
| A4722 | M-Series Loader | 8V Sensor Supply Out of Range Low |
| A4722 | Attachments | 8 Volt Sensor Supply Out of Range Low |
| A7701 | M-Series Loader | Key Switch Active |
| A7701 | Attachments | Cab Key Switch Active |
| A7901 | Attachments | E-Stop Active |
| A8002 | Attachments | Output A Error On |
| A8003 | Attachments | Output A Error Off |
| A8005 | Attachments | Output A Short to Battery |
| A8006 | Attachments | Output A Short to Ground |
| A8007 | Attachments | Output A Open Circuit |
| A8032 | Attachments | Output A Overcurrent |
| A8102 | Attachments | Output B Error On |
| A8103 | Attachments | Output B Error Off |
| A8105 | Attachments | Output B Short to Battery |
| A8106 | Attachments | Output B Short to Ground |
| A8107 | Attachments | Output B Open Circuit |
| A8132 | Attachments | Output B Overcurrent |
| A8202 | Attachments | Output C Error On |
| A8203 | Attachments | Output C Error Off |
| A8205 | Attachments | Output C Short to Battery |
| A8206 | Attachments | Output C Short to Ground |
| A8207 | Attachments | Output C Open Circuit |
| A8232 | Attachments | Output C Overcurrent |
| A8302 | Attachments | Output D Error On |
| A8303 | Attachments | Output D Error Off |
| A8305 | Attachments | Output D Short to Battery |
| A8306 | Attachments | Output D Short to Ground |
| A8307 | Attachments | Output D Open Circuit |
| A8332 | Attachments | Output D Overcurrent |
| A8402 | Attachments | Output E Error On |
| A8403 | Attachments | Output E Error Off |
| A8405 | Attachments | Output E Short to Battery |
| A8406 | Attachments | Output E Short to Ground |
| A8407 | Attachments | Output E Open Circuit |
| A8432 | Attachments | Output E Overcurrent |
| A8502 | Attachments | Output F Error On |
| A8503 | Attachments | Output F Error Off |
| A8505 | Attachments | Output F Short to Battery |
| A8506 | Attachments | Output F Short to Ground |
| A8507 | Attachments | Output F Open Circuit |
| A8532 | Attachments | Output F Overcurrent |
| A8602 | Attachments | Output G Error On |
| A8603 | Attachments | Output G Error Off |
| A8605 | Attachments | Output G Short to Battery |
| A8606 | Attachments | Output G Short to Ground |
| A8607 | Attachments | Output G Open Circuit |
| A8702 | Attachments | Output H Error On |
| A8703 | Attachments | Output H Error Off |
| A8705 | Attachments | Output H Short to Battery |
| A8706 | Attachments | Output H Short to Ground |
| A8707 | Attachments | Output H Open Circuit |
| A8802 | Attachments | Reverse Solenoid Error On |
| A8803 | Attachments | Reverse Solenoid Error Off |
| B1001-96 | Compact Wheel Loader | Key Switch Failure |
| B1001-96 | Toolcat | Key Switch – Component Internal Failure |
| B1005-00 | M-Series Loader | Key Switch Multiple |
| B1005-00 | Compact Wheel Loader | Key Switch Multiple |
| B102A-16 | Toolcat | Cab Controller Sensor Supply – Circuit Voltage Below Threshold |
| B102A-16 | M-Series Loader | Cab Controller Sensor Supply Voltage Out of Range Low |
| B102A-17 | M-Series Loader | Cab Controller Sensor Supply Voltage Out of Range High |
| B102A-17 | Toolcat | Cab Controller Sensor Supply – Circuit Voltage Above Threshold |
| B1030-11 | M-Series Loader | Front Work Light (Left Side) Short to Ground |
| B1030-12 | M-Series Loader | Front Work Light (Left Side) Short to Battery |
| B1030-13 | M-Series Loader | Front Work Light (Left Side) Not Connected |
| B1031-11 | M-Series Loader | Front Work Light (Right Side) Short to Ground |
| B1031-12 | M-Series Loader | Front Work Light (Right Side) Short to Battery |
| B1031-13 | M-Series Loader | Front Work Light (Right Side) Not Connected |
| B1034-11 | Toolcat | Rear Work Lights – Circuit Short to Ground |
| B1034-11 | Compact Wheel Loader | Rear Work Light Short to Battery |
| B1034-12 | M-Series Loader | Rear Work Lights Error On |
| B1034-12 | Toolcat | Rear Work Lights – Circuit Short to Battery |
| B1034-12 | Compact Wheel Loader | Rear Work Light Short to Ground |
| B1034-13 | Toolcat | Rear Work Lights – Circuit Open |
| B1034-13 | Compact Wheel Loader | Rear Work Light Not Connected |
| B1034-14 | M-Series Loader | Rear Work Lights Error Off |
| B1035-12 | M-Series Loader | Rear Marker Light Short to Battery |
| B1035-14 | M-Series Loader | Rear Marker Light Short to Ground or Open Circuit |
| B1036-11 | Toolcat | Rear Marker Lights – Circuit Short to Ground |
| B1036-12 | Toolcat | Rear Marker Lights – Circuit Short to Battery |
| B1036-12 | M-Series Loader | Rear Tail Lights Error On |
| B1036-13 | Toolcat | Rear Marker Lights – Circuit Open |
| B1036-14 | M-Series Loader | Rear Tail Lights Error Off |
| B1037-11 | Toolcat | Stop Lights – Circuit Short to Ground |
| B1037-11 | Compact Wheel Loader | Stop Light Short to Ground |
| B1037-12 | M-Series Loader | Stop Lamp Short to Battery |
| B1037-12 | Toolcat | Stop Lights – Circuit Short to Battery |
| B1037-13 | Toolcat | Stop Lights – Circuit Open |
| B1037-14 | M-Series Loader | Stop Lamp Short to Ground or Open Circuit |
| B1037-15 | Compact Wheel Loader | Stop Light Error On |
| B1038-12 | M-Series Loader | Registration Plate Lamp Short to Battery |
| B1038-14 | M-Series Loader | Registration Plate Lamp Short to Ground or Open Circuit |
| B1039-11 | M-Series Loader | Side Lights Short to Ground |
| B1039-12 | M-Series Loader | Side Lights Short to Battery |
| B1039-13 | M-Series Loader | Side Lights Not Connected |
| B103B-12 | Small Articulated Loader | Light Circuit Short to Battery |
| B103B-14 | Small Articulated Loader | Light Circuit Short to Ground |
| B103D-11 | Compact Wheel Loader | Beacon Short to Ground |
| B103D-12 | Compact Wheel Loader | Beacon Short to Battery |
| B103D-12 | Toolcat | Beacon Light – Circuit Short to Battery |
| B103D-13 | Compact Wheel Loader | Beacon Not Connected |
| B103D-14 | Toolcat | Beacon Light – Circuit Short to Ground or Open |
| B1040-11 | Compact Wheel Loader | Buzzer Error Off |
| B1040-12 | Compact Wheel Loader | Buzzer Error On |
| B1040-12 | Toolcat | Buzzer – Circuit Short to Battery |
| B1040-14 | Toolcat | Buzzer – Circuit Short to Ground or Open |
| B1040-14 | M-Series Loader | Buzzer Error Off |
| B1041-12 | Toolcat | Backup Alarm – Circuit Short to Battery |
| B1041-12 | Compact Wheel Loader | Backup Alarm Error Off |
| B1041-12 | M-Series Loader | Backup Alarm Error On |
| B1041-14 | M-Series Loader | Backup Alarm Error Off |
| B1041-14 | Compact Wheel Loader | Backup Alarm Error On |
| B1041-14 | Toolcat | Backup Alarm – Circuit Short to Ground or Open |
| B1042-12 | Toolcat | Horn Output – Circuit Short to Battery |
| B1042-12 | M-Series Loader | Horn Relay Short to Battery |
| B1042-14 | Toolcat | Horn Output – Circuit Short to Ground or Open |
| B1042-14 | M-Series Loader | Horn Relay Short to Ground or Open Circuit |
| B104A-11 | Compact Wheel Loader | Seat Heater Short to Ground |
| B104A-12 | Compact Wheel Loader | Seat Heater Short to Battery |
| B104A-13 | Compact Wheel Loader | Seat Heater Open Circuit |
| B1050-12 | M-Series Loader | HVAC Output Short to Battery |
| B1050-12 | Toolcat | HVAC Output – Circuit Short to Battery |
| B1050-14 | M-Series Loader | HVAC Output Short to Ground or Open Circuit |
| B1050-14 | Toolcat | HVAC Output – Circuit Short to Ground or Open |
| B1051-93 | M-Series Loader | HVAC Inside Sensor In Error |
| B1052-93 | M-Series Loader | HVAC Device Sensor In Error |
| B1053-93 | M-Series Loader | HVAC Coil Sensor In Error |
| B1054-11 | M-Series Loader | HVAC Clutch Output Error Off |
| B1054-12 | M-Series Loader | HVAC Clutch Output Error On |
| B1054-13 | M-Series Loader | HVAC Clutch Output Open Circuit |
| B1054-19 | M-Series Loader | HVAC Clutch Output Overcurrent |
| B1055-93 | M-Series Loader | HVAC Water Valve In Error |
| B105A-12 | Toolcat | Front Window Defroster Output – Circuit Short to Battery |
| B105A-14 | Toolcat | Front Window Defroster Output – Circuit Short to Ground or Open |
| B1060-93 | M-Series Loader | Lift Pedal In Error |
| B1060-F0 | M-Series Loader | Lift Pedal Not in Neutral |
| B1061-16 | M-Series Loader | Lift Pedal Sensor A Out of Range Low |
| B1061-17 | M-Series Loader | Lift Pedal Sensor A Out of Range High |
| B1062-16 | M-Series Loader | Lift Pedal Position Sensor “B” Out of Range Low |
| B1062-17 | M-Series Loader | Lift Pedal Position Sensor “B” Out of Range High |
| B1063-00 | M-Series Loader | Lift Pedal Sensor In Error |
| B1064-F0 | Compact Wheel Loader | Lift Input Not in Neutral |
| B1064-F0 | M-Series Loader | Lift Joystick Not in Neutral |
| B1065-F0 | M-Series Loader | Lift Input Not in Neutral |
| B1070-09 | M-Series Loader | Tilt Pedal Failure |
| B1070-93 | M-Series Loader | Tilt Pedal In Error |
| B1070-F0 | M-Series Loader | Tilt Pedal Not in Neutral |
| B1071-16 | M-Series Loader | Tilt Pedal Sensor A Out of Range Low |
| B1071-17 | M-Series Loader | Tilt Pedal Sensor A Out of Range High |
| B1072-16 | M-Series Loader | Tilt Pedal Position Sensor “B” Out of Range High |
| B1072-17 | M-Series Loader | Tilt Pedal Position Sensor “B” Out of Range Low |
| B1073-00 | M-Series Loader | Tilt Pedal Sensor In Error |
| B1074-F0 | Compact Wheel Loader | Tilt Input Not in Neutral |
| B1074-F0 | M-Series Loader | Tilt Joystick Not in Neutral |
| B1075-F0 | M-Series Loader | Tilt Input Not in Neutral |
| B1080-09 | Toolcat | Operator Presence – Component Failure |
| B1080-09 | Compact Wheel Loader | Operator Presence Component Failure |
| B1080-09 | M-Series Loader | Seat Bar Failure |
| B1080-16 | Compact Wheel Loader | Operator Presence Circuit Voltage Below Threshold |
| B1080-16 | Toolcat | Operator Presence – Circuit Voltage Below Threshold |
| B1080-16 | Small Articulated Loader | Armrest Out of Range Low |
| B1080-16 | M-Series Loader | Seat Bar Out of Range Low |
| B1080-17 | M-Series Loader | Seat Bar Out of Range High |
| B1080-17 | Small Articulated Loader | Armrest Out of Range High |
| B1080-17 | Compact Wheel Loader | Operator Presence Circuit Voltage Above Threshold |
| B1080-17 | Toolcat | Operator Presence – Circuit Voltage Above Threshold |
| B1080-54 | Small Articulated Loader | Armrest No Signal |
| B1080-66 | Small Articulated Loader | Armrest Intermittent Signal |
| B1090-00 | M-Series Loader | Door Open |
| B1091-16 | M-Series Loader | Door Sensor Out of Range Low |
| B1095-13 | M-Series Loader | Window Sensor Open Circuit |
| B1095-16 | M-Series Loader | Window Sensor Out of Range Low |
| B1095-17 | M-Series Loader | Window Sensor Out of Range High |
| B1095-95 | M-Series Loader | Window Sensor Failure |
| B10A0-12 | M-Series Loader | Wiper Output Short to Battery |
| B10A0-12 | Toolcat | Wiper Output – Circuit Short to Battery |
| B10A0-14 | M-Series Loader | Wiper Output Short to Ground or Open Circuit |
| B10A0-14 | Toolcat | Wiper Output – Circuit Short to Ground or Open |
| B10A1-12 | Toolcat | Washer Fluid Output – Circuit Short to Battery |
| B10A1-12 | M-Series Loader | Washer Fluid Output Short to Battery |
| B10A1-14 | Toolcat | Washer Fluid Output – Circuit Short to Ground or Open |
| B10A1-14 | M-Series Loader | Washer Fluid Output Short to Ground or Open Circuit |
| B10A2-11 | Compact Wheel Loader | Front Wiper Short to Ground |
| B10A2-12 | Compact Wheel Loader | Front Wiper Short to Battery |
| B10A2-13 | Compact Wheel Loader | Front Wiper Not connected |
| B10A3-11 | Compact Wheel Loader | Front Wiper High Speed Short to Ground |
| B10A3-12 | Compact Wheel Loader | Front Wiper High Speed Short to Battery |
| B10A3-13 | Compact Wheel Loader | Front Wiper High Speed Not connected |
| B10A5-11 | Compact Wheel Loader | Rear Wiper Short to Ground |
| B10A5-12 | Compact Wheel Loader | Rear Wiper Short to Battery |
| B10A5-13 | Compact Wheel Loader | Rear Wiper Not Connected |
| B10A7-11 | Compact Wheel Loader | Front Washer Short to Ground |
| B10A7-12 | Compact Wheel Loader | Front Washer Short to Battery |
| B10A7-13 | Compact Wheel Loader | Front Washer Not Connected |
| B10A8-11 | Compact Wheel Loader | Rear Washer Short to Ground |
| B10A8-12 | Compact Wheel Loader | Rear Washer Short to Battery |
| B10A8-13 | Compact Wheel Loader | Rear Washer Not Connected |
| B10B0-00 | M-Series Loader | Drive ISO/H Pattern Switch Flipped While Operating |
| B10B1-F0 | M-Series Loader | Drive Input Not in Neutral |
| B10B3-F0 | M-Series Loader | Drive X Input Not In Neutral |
| B10B6-F0 | M-Series Loader | Drive Y Input Not In Neutral |
| B10B9-F0 | M-Series Loader | Drive Left Input Not In Neutral |
| B10BC-F0 | M-Series Loader | Drive Right Input Not In Neutral |
| B10C0-00 | Compact Wheel Loader | Camera Not Connected |
| B10C1-00 | Toolcat | Camera Software Error |
| B10D0-11 | Toolcat | Display Switched Power Output – Circuit Short to Ground |
| B10D0-12 | Toolcat | Display Switched Power Output – Circuit Short to Battery |
| B10D0-12 | M-Series Loader | Display Switched Power Relay Error On |
| B10D0-13 | Toolcat | Display Switched Power Output – Circuit Open |
| B10D0-14 | M-Series Loader | Display Switched Power Relay Error Off |
| B10F0-11 | Compact Wheel Loader | Rear Defog Short to Ground |
| B10F0-12 | Compact Wheel Loader | Rear Defog Short to Battery |
| B10F0-13 | Compact Wheel Loader | Rear Defog Circuit Open |
| B1100-9E | Compact Wheel Loader | Power Exchange Lock Switch Stuck On |
| B1100-9E | M-Series Loader | Bobtach Engage Button Stuck On |
| B1101-9E | Compact Wheel Loader | Power Exchange Unlock Switch Stuck on |
| B1101-9E | M-Series Loader | Bobtach Disengage Button Stuck On |
| B1110-F0 | M-Series Loader | Left Primary Not in Neutral |
| B1110-F0 | Toolcat | Left Primary – Not in Neutral |
| B1111-F0 | M-Series Loader | Left Secondary Not in Neutral |
| B1111-F0 | Toolcat | Left Secondary – Not in Neutral |
| B1120-16 | Small Articulated Loader | Right Primary Out of Range Low |
| B1120-17 | Small Articulated Loader | Right Primary Out of Range High |
| B1120-F0 | Compact Wheel Loader | Joystick Right Roller Not in Neutral |
| B1120-F0 | Toolcat | Right Primary – Not in Neutral |
| B1120-F0 | M-Series Loader | Right Primary Not in Neutral |
| B1121-16 | Small Articulated Loader | Right Secondary Out of Range Low |
| B1121-17 | Small Articulated Loader | Right Secondary Out of Range High |
| B1121-F0 | Toolcat | Right Secondary – Not in Neutral |
| B1121-F0 | M-Series Loader | Right Secondary Not in Neutral |
| B1122-F0 | M-Series Loader | Detent Not in Neutral |
| B1122-F0 | Toolcat | Detent – Not in Neutral |
| B1130-F0 | Toolcat | Joystick Primary – Not in Neutral |
| B1131-F0 | Toolcat | Joystick Secondary – Not in Neutral |
| B1150-F0 | Compact Wheel Loader | FNR Lever not in Neutral |
| B1151-00 | Compact Wheel Loader | FNR Switch Multiple |
| B1155-31 | Toolcat | FPR Switch – No Signal |
| B1156-00 | Toolcat | FPR Switch Multiple |
| B116F-11 | M-Series Loader | Front Left Road Light Short to Ground |
| B116F-12 | M-Series Loader | Front Left Road Light Short to Battery |
| B116F-13 | M-Series Loader | Front Left Road Light Open Circuit |
| B1170-11 | Toolcat | Head Light High Left – Circuit Short to Ground |
| B1170-12 | Toolcat | Head Light High Left – Circuit Short to Battery |
| B1170-13 | Toolcat | Head Light High Left – Circuit Open |
| B1172-11 | Toolcat | Front Turn Signal Left – Circuit Short to Ground |
| B1172-12 | Toolcat | Front Turn Signal Left – Circuit Short to Battery |
| B1172-13 | Toolcat | Front Turn Signal Left – Circuit Open |
| B1175-11 | Toolcat | Rear Turn Signal Left – Circuit Short to Ground |
| B1175-12 | Toolcat | Rear Turn Signal Left – Circuit Short to Battery |
| B1175-13 | Toolcat | Rear Turn Signal Left – Circuit Open |
| B1177-12 | M-Series Loader | Left Turn Signal Short to Battery |
| B1177-14 | M-Series Loader | Left Turn Signal Short to Ground or Open Circuit |
| B117F-11 | M-Series Loader | Front Right Road Light Short to Ground |
| B117F-12 | M-Series Loader | Front Right Road Light Short to Battery |
| B117F-13 | M-Series Loader | Front Right Road Light Open Circuit |
| B1180-11 | Toolcat | Head Light High Right – Circuit Short to Ground |
| B1180-12 | Toolcat | Head Light High Right – Circuit Short to Battery |
| B1180-13 | Toolcat | Head Light High Right – Circuit Open |
| B1182-11 | Toolcat | Front Turn Signal Right – Circuit Short to Ground |
| B1182-12 | Toolcat | Front Turn Signal Right – Circuit Short to Battery |
| B1182-13 | Toolcat | Front Turn Signal Right – Circuit Open |
| B1185-11 | Toolcat | Rear Turn Signal Right – Circuit Short to Ground |
| B1185-12 | Toolcat | Rear Turn Signal Right – Circuit Short to Battery |
| B1185-13 | Toolcat | Rear Turn Signal Right – Circuit Open |
| B1187-12 | M-Series Loader | Right Turn Signal Short to Battery |
| B1187-14 | M-Series Loader | Right Turn Signal Short to Ground or Open Circuit |
| B1190-11 | Compact Wheel Loader | Front Work Light Short to Battery |
| B1190-11 | Toolcat | Front Work Lights – Circuit Short to Ground |
| B1190-12 | Compact Wheel Loader | Front Work Light Short to Ground |
| B1190-12 | Toolcat | Front Work Lights – Circuit Short to Battery |
| B1190-13 | Compact Wheel Loader | Front Work Light Not Connected |
| B1190-13 | Toolcat | Front Work Lights – Circuit Open |
| B1191-12 | Toolcat | Front Work Light 2 – Circuit Short to Battery |
| B1191-14 | Toolcat | Front Work Light 2 – Circuit Short to Ground or Open |
| B1192-12 | Toolcat | Front Work Light 3 – Circuit Short to Battery |
| B1192-14 | Toolcat | Front Work Light 3 – Circuit Short to Ground or Open |
| B11B0-54 | Toolcat | Travel Pedal Sensor – Missing Calibration |
| B11B0-93 | Toolcat | Travel Pedal Sensor – In Error |
| B11B1-16 | Toolcat | Travel Pedal Sensor Primary – Circuit Voltage Below Threshold |
| B11B1-17 | Toolcat | Travel Pedal Sensor Primary – Circuit Voltage Above Threshold |
| B11B2-16 | Toolcat | Travel Pedal Sensor Secondary – Circuit Voltage Below Threshold |
| B11B2-17 | Toolcat | Travel Pedal Sensor Secondary – Circuit Voltage Above Threshold |
| B11B5-54 | Compact Wheel Loader | Inching pedal sensor mising calibration |
| B11B5-54 | Toolcat | Brake Pedal Sensor – Missing Calibration |
| B11B5-93 | Toolcat | Brake Pedal Sensor – In Error |
| B11B6-16 | Toolcat | Brake Pedal Sensor Primary – Circuit Voltage Below Threshold |
| B11B6-17 | Toolcat | Brake Pedal Sensor Primary – Circuit Voltage Above Threshold |
| B11B7-16 | Toolcat | Brake Pedal Sensor Secondary – Circuit Voltage Below Threshold |
| B11B7-17 | Toolcat | Brake Pedal Sensor Secondary – Circuit Voltage Above Threshold |
| C0314 | Telehandler | LLMC Undervoltage |
| C0315 | Telehandler | LLMC Overvoltage |
| C1001-16 | Toolcat | Hub Controller Sensor Supply – Circuit Voltage Below Threshold |
| C1001-16 | Compact Wheel Loader | Sensor Supply Out of Range Low |
| C1001-17 | Toolcat | Hub Controller Sensor Supply – Circuit Voltage Above Threshold |
| C1001-17 | Compact Wheel Loader | Sensor Supply Out of Range High |
| C1002-16 | M-Series Loader | Sensor Supply Out of Range Low |
| C1002-17 | M-Series Loader | Sensor Supply Out of Range High |
| C1003-16 | Compact Wheel Loader | Sensor Supply Out of Range Low |
| C1003-17 | Compact Wheel Loader | Sensor Supply Out of Range High |
| C1004-16 | Compact Wheel Loader | Drive Controller Sensor Supply Out of Range Low |
| C1004-17 | Compact Wheel Loader | Drive Controller Sensor Supply Out of Range High |
| C1005-16 | Toolcat | Pump Controller Sensor Supply – Circuit Voltage Below Threshold |
| C1005-17 | Toolcat | Pump Controller Sensor Supply – Circuit Voltage Above Threshold |
| C1006-16 | Toolcat | Rear Controller Sensor Supply – Circuit Voltage Below Threshold |
| C1006-17 | Toolcat | Rear Controller Sensor Supply – Circuit Voltage Above Threshold |
| C100A-11 | M-Series Loader | ECU Power Short to Ground |
| C100A-11 | Toolcat | ECU Power – Circuit Short to Ground |
| C100A-12 | Toolcat | ECU Power – Circuit Short to Battery |
| C100A-12 | M-Series Loader | ECU Power Short to Battery |
| C100A-13 | M-Series Loader | ECU Power Open Circuit |
| C100A-13 | Toolcat | ECU Power – Circuit Open |
| C1015-16 | M-Series Loader | Lift Spool Position Sensor Out of Range Low |
| C1015-17 | M-Series Loader | Lift Spool Position Sensor Out of Range High |
| C1015-56 | M-Series Loader | Lift Spool Position Sensor Inverted Movement |
| C1015-93 | M-Series Loader | Lift Spool Position Sensor Unresponsive |
| C1015-F0 | M-Series Loader | Lift Spool Position Sensor Not in Neutral |
| C1016-16 | M-Series Loader | Tilt Spool Position Sensor Out of Range Low |
| C1016-17 | M-Series Loader | Tilt Spool Position Sensor Out of Range High |
| C1016-93 | M-Series Loader | Tilt Spool Position Sensor Unresponsive |
| C1016-F0 | M-Series Loader | Tilt Spool Position Sensor Not in Neutral |
| C101A-16 | Compact Wheel Loader | Lift Base Pressure Out of Range Low |
| C101A-17 | Compact Wheel Loader | Lift Base Pressure Out of Range High |
| C101D-16 | M-Series Loader | Tilt Rod Pressure Sensor Out of Range Low |
| C101D-17 | M-Series Loader | Tilt Rod Pressure Sensor Out of Range High |
| C1020-11 | Compact Wheel Loader | Front Base Solenoid Short to Ground |
| C1020-11 | Toolcat | Front Aux Base Solenoid – Circuit Short to Ground |
| C1020-12 | Compact Wheel Loader | Front Base Solenoid Short to Battery |
| C1020-12 | Toolcat | Front Aux Base Solenoid – Circuit Short to Battery |
| C1020-13 | Compact Wheel Loader | Front Base Solenoid Open Circuit |
| C1020-13 | Toolcat | Front Aux Base Solenoid – Circuit Open |
| C1020-19 | Compact Wheel Loader | Front Base Solenoid Overcurrent |
| C1020-19 | Toolcat | Front Aux Base Solenoid – Circuit Current Above Threshold |
| C1021-11 | Toolcat | Front Aux Rod Solenoid – Circuit Short to Ground |
| C1021-11 | Compact Wheel Loader | Front Rod Solenoid Short to Ground |
| C1021-12 | Toolcat | Front Aux Rod Solenoid – Circuit Short to Battery |
| C1021-12 | Compact Wheel Loader | Front Rod Solenoid Short to Battery |
| C1021-13 | Compact Wheel Loader | Front Rod Solenoid Open Circuit |
| C1021-13 | Toolcat | Front Aux Rod Solenoid – Circuit Open |
| C1021-19 | Compact Wheel Loader | Front Rod Solenoid Overcurrent |
| C1021-19 | Toolcat | Front Aux Rod Solenoid – Circuit Current Above Threshold |
| C1024-11 | Toolcat | Diverter Solenoid – Circuit Short to Ground |
| C1024-12 | Toolcat | Diverter Solenoid – Circuit Short to Battery |
| C1024-13 | Toolcat | Diverter Solenoid – Circuit Open |
| C1026-11 | Toolcat | Remote Hydraulics Output – Circuit Short to Ground |
| C1026-12 | Toolcat | Remote Hydraulics Output – Circuit Short to Battery |
| C1026-13 | Toolcat | Remote Hydraulics Output – Circuit Open |
| C1029-11 | M-Series Loader | Hydraulic Lock Solenoid Short to Ground |
| C1029-12 | M-Series Loader | Hydraulic Lock Solenoid Short to Battery |
| C1029-13 | M-Series Loader | Hydraulic Lock Solenoid Open Circuit |
| C102A-11 | Compact Wheel Loader | Hydraulic Fan Short to Ground |
| C102A-11 | Toolcat | Hydraulic Fan Solenoid – Circuit Short to Ground |
| C102A-12 | Toolcat | Hydraulic Fan Solenoid – Circuit Short to Battery |
| C102A-12 | Compact Wheel Loader | Hydraulic Fan Short to Battery |
| C102A-13 | Compact Wheel Loader | Hydraulic Cooling Fan Electrical Problem |
| C102A-13 | Toolcat | Hydraulic Fan Solenoid – Circuit Open |
| C102A-19 | Toolcat | Hydraulic Fan Solenoid – Circuit Current Above Threshold |
| C102A-19 | Compact Wheel Loader | Hydraulic Fan Overcurrent |
| C102B-11 | M-Series Loader | Reverse Fan Short to Ground |
| C102B-12 | M-Series Loader | Reverse Fan Short to Battery |
| C102B-13 | M-Series Loader | Reverse Fan Open Circuit |
| C102E-12 | Small Articulated Loader | Fan Circuit Short to Battery |
| C102E-14 | Small Articulated Loader | Fan Open Circuit |
| C1030-00 | M-Series Loader | Two Speed Shift Not Allowed |
| C1032-11 | M-Series Loader | Brake Pull Output Short to Ground |
| C1032-12 | M-Series Loader | Brake Pull Output Short to Battery |
| C1032-13 | M-Series Loader | Brake Pull Output Open Circuit |
| C1033-11 | M-Series Loader | Left Brake Hold Output Short to Ground |
| C1033-12 | M-Series Loader | Left Brake Hold Output Short to Battery |
| C1033-13 | M-Series Loader | Left Brake Hold Output Open Circuit |
| C1034-11 | M-Series Loader | Right Brake Hold Output Short to Ground |
| C1034-12 | M-Series Loader | Right Brake Hold Output Short to Battery |
| C1034-13 | M-Series Loader | Right Brake Hold Output Open Circuit |
| C1035-16 | M-Series Loader | Left Brake Pull Relay Error Off |
| C1035-17 | M-Series Loader | Left Brake Pull Relay Error On |
| C1036-16 | M-Series Loader | Right Brake Pull Relay Error Off |
| C1036-17 | M-Series Loader | Right Brake Pull Relay Error On |
| C1039-11 | Toolcat | High Flow Solenoid – Circuit Short to Ground |
| C1039-11 | Compact Wheel Loader | High Flow Solenoid Short to Ground |
| C1039-12 | Toolcat | High Flow Solenoid – Circuit Short to Battery |
| C1039-12 | Compact Wheel Loader | High Flow Solenoid Short to Battery |
| C1039-13 | Compact Wheel Loader | High Flow Solenoid Open Circuit |
| C1039-13 | Toolcat | High Flow Solenoid – Circuit Open |
| C1039-19 | M-Series Loader | High Flow Solenoid Overcurrent |
| C103A-11 | M-Series Loader | Ride Control 1 Short to Ground |
| C103A-12 | M-Series Loader | Ride Control 1 Short to Battery |
| C103A-13 | M-Series Loader | Ride Control 1 Open Circuit |
| C103B-11 | M-Series Loader | Ride Control 2 Short to Ground |
| C103B-12 | M-Series Loader | Ride Control 2 Short to Battery |
| C103B-13 | M-Series Loader | Ride Control 2 Open Circuit |
| C103C-11 | M-Series Loader | Bobtach Engage Short to Ground |
| C103C-11 | Toolcat | Bobtach Engage Solenoid – Circuit Short to Ground |
| C103C-12 | M-Series Loader | Bobtach Engage Short to Battery |
| C103C-12 | Toolcat | Bobtach Engage Solenoid – Circuit Short to Battery |
| C103C-13 | Toolcat | Bobtach Engage Solenoid – Circuit Open |
| C103C-13 | M-Series Loader | Bobtach Engage Open Circuit |
| C103D-11 | Toolcat | Bobtach Disengage Solenoid – Circuit Short to Ground |
| C103D-11 | M-Series Loader | Bobtach Disengage Short to Ground |
| C103D-12 | Toolcat | Bobtach Disengage Solenoid – Circuit Short to Battery |
| C103D-12 | M-Series Loader | Bobtach Disengage Short to Battery |
| C103D-13 | M-Series Loader | Bobtach Disengage Open Circuit |
| C103D-13 | Toolcat | Bobtach Disengage Solenoid – Circuit Open |
| C1040-11 | M-Series Loader | Lift Actuator Short to Ground |
| C1040-12 | M-Series Loader | Lift Actuator Short to Battery |
| C1040-13 | M-Series Loader | Lift Actuator Open Circuit |
| C1040-19 | M-Series Loader | Lift Actuator Overcurrent |
| C1040-77 | M-Series Loader | Lift Actuator Reduced Performance |
| C1041-00 | M-Series Loader | Lift Spool Position Sensor Inverted Movement |
| C1042-00 | M-Series Loader | Lift Actuator Uncommanded Motion |
| C1043-11 | Compact Wheel Loader | Lift Cylinder Base Short to Ground |
| C1043-12 | Compact Wheel Loader | Lift Cylinder Base Short to Battery |
| C1043-13 | Compact Wheel Loader | Lift Cylinder Base Open Circuit |
| C1043-19 | Compact Wheel Loader | Lift Cylinder Base Overcurrent |
| C1044-11 | Compact Wheel Loader | Lift Cylinder Rod Short to Ground |
| C1044-12 | Compact Wheel Loader | Lift Cylinder Rod Short to Battery |
| C1044-13 | Compact Wheel Loader | Lift Cylinder Rod Open Circuit |
| C1044-19 | Compact Wheel Loader | Lift Cylinder Rod Overcurrent |
| C1045-11 | M-Series Loader | Tilt Actuator Short to Ground |
| C1045-12 | M-Series Loader | Tilt Actuator Short to Battery |
| C1045-13 | M-Series Loader | Tilt Actuator Open Circuit |
| C1045-19 | M-Series Loader | Tilt Actuator Overcurrent |
| C1045-77 | M-Series Loader | Tilt Actuator Reduced Performance |
| C1046-00 | M-Series Loader | Tilt Spool Position Sensor Inverted Movement |
| C1047-00 | M-Series Loader | Tilt Actuator Uncommanded Motion |
| C1048-11 | Compact Wheel Loader | Tilt Cylinder Rod Short to Ground |
| C1048-12 | Compact Wheel Loader | Tilt Cylinder Rod Short to Battery |
| C1048-13 | Compact Wheel Loader | Tilt Cylinder Rod Open Circuit |
| C1048-19 | Compact Wheel Loader | Tilt Cylinder Rod Overcurrent |
| C1049-11 | Compact Wheel Loader | Tilt Cylinder Base Short to Ground |
| C1049-12 | Compact Wheel Loader | Tilt Cylinder Base Short to Battery |
| C1049-13 | Compact Wheel Loader | Tilt Cylinder Base Open Circuit |
| C1049-19 | Compact Wheel Loader | Tilt Cylinder Base Overcurrent |
| C104A-00 | M-Series Loader | Lift Float Failed to achieve float |
| C104B-00 | M-Series Loader | Lift Float Conditions not favorable |
| C104C-00 | M-Series Loader | Lift Float Failed to maintain float |
| C1050-11 | Compact Wheel Loader | Switched Power Relay Short to Ground |
| C1050-12 | Toolcat | Switched Power Output – Circuit Short to Battery |
| C1050-12 | Compact Wheel Loader | Switched Power Relay Short to Battery |
| C1050-13 | Compact Wheel Loader | Switched Power Relay Open Circuit |
| C1050-14 | Toolcat | Switched Power Output – Circuit Short to Ground or Open |
| C1050-15 | Small Articulated Loader | Switched Power Relay Short to Battery or Open Circuit |
| C1051-11 | M-Series Loader | Two Speed Solenoid Short to Ground |
| C1051-11 | Toolcat | Two Speed Solenoid – Circuit Short to Ground |
| C1051-12 | M-Series Loader | Two Speed Solenoid Short to Battery |
| C1051-12 | Toolcat | Two Speed Solenoid – Circuit Short to Battery |
| C1051-13 | Toolcat | Two Speed Solenoid – Circuit Open |
| C1051-13 | M-Series Loader | Two Speed Solenoid Open Circuit |
| C1051-19 | M-Series Loader | Two Speed Solenoid Overcurrent |
| C1060-11 | Compact Wheel Loader | Brake Short to Ground |
| C1060-11 | Small Articulated Loader | Brake Solenoid Short to Ground |
| C1060-12 | Small Articulated Loader | Brake Solenoid Short to Battery |
| C1060-12 | Compact Wheel Loader | Brake Short to Battery |
| C1060-13 | Small Articulated Loader | Brake Solenoid Open Circuit |
| C1060-13 | Compact Wheel Loader | Brake Open Circuit |
| C1060-19 | Compact Wheel Loader | Brake Solenoid Overcurrent |
| C1061-11 | Toolcat | Brake 1 Solenoid – Circuit Short to Ground |
| C1061-12 | Toolcat | Brake 1 Solenoid – Circuit Short to Battery |
| C1061-13 | Toolcat | Brake 1 Solenoid – Circuit Open |
| C1061-19 | Toolcat | Brake 1 Solenoid – Circuit Current Above Threshold |
| C1062-11 | Toolcat | Brake 2 Solenoid – Circuit Short to Ground |
| C1062-12 | Toolcat | Brake 2 Solenoid – Circuit Short to Battery |
| C1062-13 | Toolcat | Brake 2 Solenoid – Circuit Open |
| C1062-19 | Toolcat | Brake 2 Solenoid – Circuit Current Above Threshold |
| C1070-11 | M-Series Loader | Rear Auxiliary Base Solenoid Short to Ground |
| C1070-12 | M-Series Loader | Rear Auxiliary Base Solenoid Short to Battery |
| C1070-13 | M-Series Loader | Rear Auxiliary Base Solenoid Open Circuit |
| C1071-11 | M-Series Loader | Rear Auxiliary Base Lock Solenoid Short to Ground |
| C1071-12 | M-Series Loader | Rear Auxiliary Base Lock Solenoid Short to Battery |
| C1071-13 | M-Series Loader | Rear Auxiliary Base Lock Open Circuit |
| C1075-11 | M-Series Loader | Rear Auxiliary Rod Solenoid Short to Ground |
| C1075-12 | M-Series Loader | Rear Auxiliary Rod Solenoid Short to Battery |
| C1075-13 | M-Series Loader | Rear Auxiliary Rod Solenoid Open Circuit |
| C1076-11 | M-Series Loader | Rear Auxiliary Rod Lock Solenoid Short to Ground |
| C1076-12 | M-Series Loader | Rear Auxiliary Rod Lock Solenoid Short to Battery |
| C1076-13 | M-Series Loader | Rear Auxiliary Rod Solenoid Open Circuit |
| C1080-F8 | M-Series Loader | Hydraulic Charge Pressure Extremely Low |
| C1080-F9 | M-Series Loader | Low Hydraulic Pump Pressure |
| C1080-FA | M-Series Loader | Hydraulic Charge Pressure High |
| C1080-FB | M-Series Loader | Hydraulic Charge Pressure Extremely High |
| C1080-FD | Small Articulated Loader | Hydraulic Charge Pressure Shutdown |
| C1090-00 | Toolcat | Hydraulic Main Filter Plugged |
| C1090-00 | Compact Wheel Loader | Hydraulic Filter Plugged |
| C1091-16 | Toolcat | Hydraulic Main Filter Switch – Circuit Voltage Below Threshold |
| C1091-17 | Toolcat | Hydraulic Main Filter Switch – Circuit Voltage Above Threshold |
| C1091-95 | Toolcat | Hydraulic Main Filter Pressure Switch – Incorrect Assembly |
| C1091-95 | Compact Wheel Loader | Hydraulic Main Filter Switch Not Connected |
| C1093-00 | M-Series Loader | Hydraulic Case Drain Filter Switch Plugged |
| C1097-16 | M-Series Loader | Hydraulic Charge Pressure Sensor Out of Range Low |
| C1097-17 | M-Series Loader | Hydraulic Charge Pressure Sensor Out of Range High |
| C1099-FA | Toolcat | Hydraulic Oil Temperature – High |
| C1099-FA | Compact Wheel Loader | Hydraulic Oil Temperature Too High |
| C1099-FB | Compact Wheel Loader | Hydraulic Oil Temperature Extremely High |
| C1099-FB | Toolcat | Hydraulic Oil Temperature – Extremely High |
| C1099-FC | Compact Wheel Loader | Hydraulic Oil Temperature Performance Reduction |
| C1099-FD | Small Articulated Loader | Hydraulic Oil Temperature Shutdown |
| C109A-16 | Toolcat | Hydraulic Oil Temperature Sensor – Circuit Voltage Below Threshold |
| C109A-16 | Compact Wheel Loader | Hydraulic Oil Temperature Out of Range Low |
| C109A-17 | Compact Wheel Loader | Hydraulic Oil Temperature Out of Range High |
| C109A-17 | Toolcat | Hydraulic Oil Temperature Sensor – Circuit Voltage Above Threshold |
| C10A0-16 | M-Series Loader | Drive Motor Case Drain Hydraulic Oil Temperature Out of Range Low |
| C10A0-17 | M-Series Loader | Drive Motor Case Drain Hydraulic Oil Temperature Out of Range High |
| C10A1-FA | M-Series Loader | Drive Motor Case Drain Hydraulic Oil Temperature High |
| C10A1-FB | M-Series Loader | Drive Motor Case Drain Hydraulic Oil Temperature Extremely High |
| C10A1-FC | M-Series Loader | Drive Motor Case Drain Hydraulic Oil Temperature Reduced Performance |
| C10A5-16 | M-Series Loader | Pump Case Drain Hydraulic Oil Temperature Out of Range Low |
| C10A5-17 | M-Series Loader | Pump Case Drain Hydraulic Oil Temperature Out of Range High |
| C10A6-FA | M-Series Loader | Pump Case Drain Hydraulic Oil Temperature High |
| C10A6-FB | M-Series Loader | Pump Case Drain Hydraulic Oil Temperature Extremely High |
| C10A6-FC | M-Series Loader | Pump Case Drain Hydraulic Oil Temperature High |
| C10B0-00 | M-Series Loader | Workgroup Disabled Due To Window Fault |
| C10C0-77 | M-Series Loader | Right Swash Plate Commanded Position Not Reachable |
| C10C0-F0 | M-Series Loader | Right Swash Plate Not in Neutral |
| C10C1-16 | M-Series Loader | Right Swash Plate Sensor Out of Range Low |
| C10C1-17 | M-Series Loader | Right Swash Plate Sensor Out of Range High |
| C10C5-77 | M-Series Loader | Left Swash Plate Commanded Position Not Reachable |
| C10C5-F0 | M-Series Loader | Left Swash Plate Not in Neutral |
| C10C6-16 | M-Series Loader | Left Swash Plate Sensor Out of Range Low |
| C10C6-17 | M-Series Loader | Left Swash Plate Sensor Out of Range High |
| C10CA-77 | Toolcat | Swash Plate – Commanded Position Not Reachable |
| C10CA-F0 | Toolcat | Swash Plate – Not in Neutral |
| C10CB-16 | Toolcat | Swash Plate Sensor – Circuit Voltage Below Threshold |
| C10CB-17 | Toolcat | Swash Plate Sensor – Circuit Voltage Above Threshold |
| C10D0-54 | M-Series Loader | Drive Pump Not Calibrated |
| C10D0-54 | Toolcat | Drive Pump – Missing Calibration |
| C10D1-11 | Toolcat | Drive Pump Forward – Circuit Short to Ground |
| C10D1-11 | Compact Wheel Loader | Drive Pump Forward Short to Ground |
| C10D1-12 | Toolcat | Drive Pump Forward – Circuit Short to Battery |
| C10D1-12 | Compact Wheel Loader | Drive Pump Forward Short to Battery |
| C10D1-13 | Compact Wheel Loader | Drive Pump Forward Open Circuit |
| C10D1-13 | Toolcat | Drive Pump Forward – Circuit Open |
| C10D1-19 | Compact Wheel Loader | Drive Pump Forward Overcurrent |
| C10D1-19 | Toolcat | Drive Pump Forward – Circuit Current Above Threshold |
| C10D2-11 | Compact Wheel Loader | Drive Pump reverse Short to Ground |
| C10D2-11 | Toolcat | Drive Pump Reverse – Circuit Short to Ground |
| C10D2-12 | Toolcat | Drive Pump Reverse – Circuit Short to Battery |
| C10D2-12 | Compact Wheel Loader | Drive Pump reverse Short to Battery |
| C10D2-13 | Compact Wheel Loader | Drive Pump reverse Open Circuit |
| C10D2-13 | Toolcat | Drive Pump Reverse – Circuit Open |
| C10D2-19 | Compact Wheel Loader | Drive Pump reverse Overcurrent |
| C10D2-19 | Toolcat | Drive Pump Reverse – Circuit Current Above Threshold |
| C10E0-16 | Small Articulated Loader | Controller 8V Sensor Supply Voltage Low |
| C10E0-17 | Small Articulated Loader | Controller 8V Sensor Supply Voltage High |
| C10E5-16 | Small Articulated Loader | Controller 5V Sensor Supply Voltage Low |
| C10E5-17 | Small Articulated Loader | Controller 5V Sensor Supply Voltage High |
| C10F0-11 | Small Articulated Loader | Lift/Tilt Short to Ground |
| C10F0-12 | Small Articulated Loader | Lift/Tilt Short to Battery |
| C10F0-13 | Small Articulated Loader | Lift/Tilt Open Circuit |
| C10F1-16 | Small Articulated Loader | Lift/Tilt Out of Range Low |
| C10F1-17 | Small Articulated Loader | Lift/Tilt Out of Range High |
| C10FA-11 | Small Articulated Loader | Lift Arm Extension Short to Ground |
| C10FA-12 | Small Articulated Loader | Lift Arm Extension Short to Battery |
| C10FA-13 | Small Articulated Loader | Lift Arm Extension Open Circuit |
| C10FA-19 | Small Articulated Loader | Lift Arm Extension Overcurrent |
| C10FB-11 | Small Articulated Loader | Lift Arm Rod Solenoid Short to Ground |
| C10FB-12 | Small Articulated Loader | Lift Arm Rod Solenoid Short to Battery |
| C10FB-13 | Small Articulated Loader | Lift Arm Rod Solenoid Open Circuit |
| C10FB-19 | Small Articulated Loader | Lift Arm Rod Solenoid Overcurrent |
| C10FC-11 | Small Articulated Loader | Lift Arm Base Solenoid Short to Ground |
| C10FC-12 | Small Articulated Loader | Lift Arm Base Solenoid Short to Battery |
| C10FC-13 | Small Articulated Loader | Lift Arm Solenoid Open Circuit |
| C10FC-19 | Small Articulated Loader | Lift Arm Solenoid Overcurrent |
| C1100-11 | Small Articulated Loader | Travel Circuit Short to Ground |
| C1100-12 | Small Articulated Loader | Travel Circuit Short to Battery |
| C1100-13 | Small Articulated Loader | Travel Circuit Open |
| C1101-16 | Small Articulated Loader | Travel Circuit Our of Range Low |
| C1101-17 | Small Articulated Loader | Travel Circuit Out of Range High |
| C1110-11 | Compact Wheel Loader | Ride Control Circuit Short to Ground |
| C1110-15 | Compact Wheel Loader | Ride Control Circuit Error On |
| C1111-16 | Compact Wheel Loader | Ride Control Feedback Circuit Out of Range Low |
| C1111-17 | Compact Wheel Loader | Ride Control Feedback Circuit Out of Range High |
| C1130-11 | Compact Wheel Loader | Hydraulic Motor reverse Short to Ground |
| C1130-12 | Compact Wheel Loader | Hydraulic Motor reverse Short to Battery |
| C1130-13 | Compact Wheel Loader | Hydraulic Motor reverse Open Circuit |
| C1130-19 | Compact Wheel Loader | Hydraulic Motor Overcurrent |
| C1150-13 | M-Series Loader | Right Drive Motor Direction Open Circuit |
| C1150-16 | M-Series Loader | Right Drive Motor Direction Out of Range Low |
| C1150-17 | M-Series Loader | Right Drive Motor Direction Out of Range High |
| C1155-13 | M-Series Loader | Left Drive Motor Direction Open Circuit |
| C1155-16 | M-Series Loader | Left Drive Motor Direction Out of Range Low |
| C1155-17 | M-Series Loader | Left Drive Motor Direction Out of Range High |
| C1182-A2 | Small Articulated Loader | Alternator Voltage High |
| C1182-A2 | Compact Wheel Loader | Alternator Voltage Low |
| C1182-A2 | Toolcat | Alternator Voltage System Voltage Low |
| C1182-A3 | Toolcat | Alternator Voltage System Voltage High |
| C1182-A3 | Small Articulated Loader | Alternator Voltage Low |
| C1182-A3 | M-Series Loader | Alternator Voltage High |
| C1183-A3 | Compact Wheel Loader | Alternator Voltage High |
| C1190-00 | M-Series Loader | System Voltage Out of Range Low |
| C1192-00 | Compact Wheel Loader | System Voltage Extremely Low |
| C1192-00 | Toolcat | Battery Voltage Extremely Low |
| C1193-00 | Toolcat | Battery Voltage Low |
| C1193-00 | Compact Wheel Loader | System Voltage Too Low |
| C1195-00 | M-Series Loader | System Voltage Extremely Low |
| C1195-00 | Toolcat | Battery Voltage High |
| C1195-00 | Compact Wheel Loader | System Voltage High |
| C1196-00 | Compact Wheel Loader | System Voltage Extremely High |
| C1196-00 | Toolcat | Battery Voltage Extremely High |
| C119A-F8 | Small Articulated Loader | System Voltage Extremely Low |
| C119A-F9 | Small Articulated Loader | System Voltage Too Low |
| C119A-FA | Small Articulated Loader | System Voltage Extremely Low |
| C119A-FB | Small Articulated Loader | System Voltage Extremely High |
| C11A0-11 | Toolcat | Servo Enable Solenoid – Circuit Short to Ground |
| C11A0-12 | Toolcat | Servo Enable Solenoid – Circuit Short to Battery |
| C11A0-13 | Toolcat | Servo Enable Solenoid – Circuit Open |
| C11C0-11 | M-Series Loader | Left Forward Drive Solenoid Error Off |
| C11C0-12 | M-Series Loader | Left Forward Drive Solenoid Error On |
| C11C2-11 | M-Series Loader | Left Reverse Drive Solenoid Error Off |
| C11C2-12 | M-Series Loader | Left Reverse Drive Solenoid Error On |
| C11C4-11 | M-Series Loader | Right Forward Drive Solenoid Error Off |
| C11C4-12 | M-Series Loader | Right Forward Drive Solenoid Error On |
| C11C6-11 | M-Series Loader | Right Reverse Drive Solenoid Error Off |
| C11C6-12 | M-Series Loader | Right Reverse Drive Solenoid Error On |
| C11F0-94 | Toolcat | Diverter Switch – Unexpected Operation |
| C1200-11 | Compact Wheel Loader | Power Exchange Unlock Short to Ground |
| C1200-12 | Compact Wheel Loader | Power Exchange Unlock Short to Battery |
| C1200-13 | Compact Wheel Loader | Power Exchange Unlock Open Circuit |
| C1205-11 | Compact Wheel Loader | Power Exchange Lock Short to Ground |
| C1205-12 | Compact Wheel Loader | Power Exchange Lock Short to Battery |
| C1205-13 | Compact Wheel Loader | Power Exchange Lock Open Circuit |
| C1220-11 | Compact Wheel Loader | Diff-Lock Short to Ground |
| C1220-12 | Compact Wheel Loader | Diff-Lock Short to Battery |
| C1220-13 | Compact Wheel Loader | Diff-Lock Open Circuit |
| C1220-19 | Compact Wheel Loader | Diff-Lock Overcurrent |
| C1221-17 | Compact Wheel Loader | Diff-Lock Sensor Out of Range High |
| C1250-F9 | Compact Wheel Loader | Park Brake Pressure Low |
| C1250-FA | Compact Wheel Loader | Park Brake Pressure High |
| C1251-16 | Compact Wheel Loader | Park Brake Pressure Sensor Circuit Out of Range Low |
| C1251-17 | Compact Wheel Loader | Park Brake Pressure Sensor Circuit Out of Range High |
| C1260-F9 | Compact Wheel Loader | Service Brake Pressure Low |
| C1260-FA | Compact Wheel Loader | Service Brake Pressure High |
| C1260-FB | Compact Wheel Loader | Service Brake Pressure Extremely High |
| C1261-16 | Compact Wheel Loader | Service Brake Pressure Sensor Circuit Out of Range Low |
| C1261-17 | Compact Wheel Loader | Service Brake Pressure Sensor Circuit Out of Range High |
| C1270-F9 | Compact Wheel Loader | Steering Pressure Low |
| C1271-16 | Compact Wheel Loader | Steering Pressure Sensor Circuit Out of Range Low |
| C1271-17 | Compact Wheel Loader | Steering Pressure Sensor Circuit Out of Range High |
| C1280-F9 | Compact Wheel Loader | Reserve Brake Pressure Low |
| C1280-FA | Compact Wheel Loader | Reserve Brake Pressure High |
| C1280-FB | Compact Wheel Loader | Reserve Brake Pressure Extremely Low |
| C1281-16 | Compact Wheel Loader | Reserve Brake Pressure Sensor Circuit Out of Range Low |
| C1281-17 | Compact Wheel Loader | Reserve Brake Pressure Sensor Circuit Out of Range High |
| C1290-17 | Toolcat | PTO Speed Sensor – Circuit Voltage Above Threshold |
| C1291-FA | Toolcat | PTO Speed – High |
| C1291-FB | Toolcat | PTO Speed – Extremely High |
| C1292-FD | Toolcat | PTO – In Shutdown |
| C1293-92 | Toolcat | PTO Switch – Performance or Incorrect Operation |
| C1295-13 | Toolcat | Traction Control Speed Sensor – Circuit Open |
| C1295-16 | Toolcat | Traction Control Speed Sensor – Circuit Voltage Below Threshold |
| C1295-17 | Toolcat | Traction Control Speed Sensor – Circuit Voltage Above Threshold |
| C129A-13 | Toolcat | Main Speed Sensor – Circuit Open |
| C129A-16 | Toolcat | Main Speed Sensor – Circuit Voltage Below Threshold |
| C129A-17 | Toolcat | Main Speed Sensor – Circuit Voltage Above Threshold |
| C12B0-11 | Toolcat | Lift Spool Lock – Circuit Short to Ground |
| C12B0-12 | Toolcat | Lift Spool Lock – Circuit Short to Battery |
| C12B0-13 | Toolcat | Lift Spool Lock – Circuit Open |
| C12B5-11 | Toolcat | Tilt Spool Lock – Circuit Short to Ground |
| C12B5-12 | Toolcat | Tilt Spool Lock – Circuit Short to Battery |
| C12B5-13 | Toolcat | Tilt Spool Lock – Circuit Open |
| C12BA-11 | Toolcat | Box Spool Lock – Circuit Short to Ground |
| C12BA-12 | Toolcat | Box Spool Lock – Circuit Short to Battery |
| C12BA-13 | Toolcat | Box Spool Lock – Circuit Open |
| C12F0-FB | Compact Wheel Loader | Hydromotor Speed Extremely High |
| C12F1-31 | Compact Wheel Loader | Hydromotor Speed Sensor Not Connected |
| C1300-16 | Compact Wheel Loader | Inching Sensor Circuit Out of Range Low |
| C1300-17 | Compact Wheel Loader | Inching Sensor Circuit Out of Range High |
| C1401-11 | Toolcat | AWS Solenoid 1 – Circuit Short to Ground |
| C1401-12 | Toolcat | AWS Solenoid 1 – Circuit Short to Battery |
| C1401-13 | Toolcat | AWS Solenoid 1 – Circuit Open |
| C1402-11 | Toolcat | AWS Solenoid 2 – Circuit Short to Ground |
| C1402-12 | Toolcat | AWS Solenoid 2 – Circuit Short to Battery |
| C1402-13 | Toolcat | AWS Solenoid 2 – Circuit Open |
| C1403-11 | Toolcat | AWS Solenoid 3 – Circuit Short to Ground |
| C1403-12 | Toolcat | AWS Solenoid 3 – Circuit Short to Battery |
| C1403-13 | Toolcat | AWS Solenoid 3 – Circuit Open |
| C3014 | Telehandler | LLMC Sensor Offset |
| C3015 | Telehandler | LLMC Sensor Out of Range |
| C3016 | Telehandler | LLMC Sensor Default |
| C3017 | Telehandler | LLMC Sensor ID Error |
| C3018 | Telehandler | LLMC Sensor Rx Out of Delay |
| C3113 | Telehandler | LLMC Calibration Values Out of Range |
| C3121 | Telehandler | LLMC Calibration Values Inverted |
| C3122 | Telehandler | LLMC Calibration Values Too Close |
| C3123 | Telehandler | LLMC Calibration Timeout |
| C3801 | Telehandler | LLMC EEPROM Failure |
| C3803 | Telehandler | LLMC External Watchdog Default |
| C3804 | Telehandler | LLMC Wrong RAM Test |
| C3805 | Telehandler | LLMC Wrong Program Checksum |
| CP706 | M-Series Loader | TestCP706 |
| D0217 | Telehandler | Hydraulic filter plugged |
| D0321 | Telehandler | Battery Voltage OOR High |
| D0322 | Telehandler | Battery Voltage OOR Low |
| D0421 | Telehandler | Inching Pedal OOR High |
| D0422 | Telehandler | Inching Pedal OOR Low |
| D0428 | Telehandler | Inching Pedal In error |
| D0605 | Telehandler | Vehicle speed Short To Battery |
| D0606 | Telehandler | Vehicle speed Short To Ground |
| D0607 | Telehandler | Vehicle speed Open circuit |
| D0611 | Telehandler | Vehicle speed extremely high |
| D0613 | Telehandler | Vehicle speed No Signal |
| D0721 | Telehandler | Hydraulic Oil Temperature OOR High |
| D0722 | Telehandler | Hydraulic Oil Temperature OOR Low |
| D0821 | Telehandler | Frame leveling Pressure Sensor Out Of Range High |
| D0822 | Telehandler | frame leveling Pressure Sensor Out Of Range Low |
| D0909 | Telehandler | Park Brake Pressure Low |
| D0910 | Telehandler | Park Brake Pressure High |
| D0911 | Telehandler | Park Brake Pressure Extremely High |
| D0921 | Telehandler | Park Brake Pressure Out of Range High |
| D0922 | Telehandler | Park Brake Pressure Out of Range Low |
| D1002 | Telehandler | Passive Brake Output Short To Battery or Open circuit |
| D1003 | Telehandler | Passive Brake Valve Short To Ground |
| D1005 | Telehandler | Passive Brake Output Short To Battery |
| D1006 | Telehandler | Passive Brake Output Short To Ground |
| D1007 | Telehandler | Passive Brake Output Open Circuit |
| D1032 | Telehandler | Passive Brake Output Overcurrent |
| D1128 | Telehandler | Park Brake Dashboard Switch In Error |
| D1145 | Telehandler | Park Brake Dashboard Switch Disagree |
| D1202 | Telehandler | EMEA Trailer Brake output Error On (Short To Battery) |
| D1203 | Telehandler | EMEA Trailer Brake output Error Off (Short To Gound) |
| D1207 | Telehandler | EMEA Trailer Brake output Open circuit |
| D1233 | Telehandler | EMEA Trailer Brake output Controller Internal failure |
| D1302 | Telehandler | EMEA Trailer Brake Relay Error On |
| D1303 | Telehandler | EMEA Trailer Brake Relay Error Off |
| D1402 | Telehandler | Brake Light Output Error On |
| D1402 | Telehandler | Trailer Brake Command Line Output Error On |
| D1403 | Telehandler | Trailer Brake Command Line Output Error Off |
| D1403 | Telehandler | Brake Light Output Error Off |
| D1407 | Telehandler | Trailer Brake Command Line Output Open Circuit |
| D1407 | Telehandler | Brake Light Output Open Circuit |
| D1433 | Telehandler | Trailer Brake Command Line Output Internal failure |
| D1433 | Telehandler | Brake Light Output Internal failure |
| D1502 | Telehandler | Trailer Brake Command Line Relay Error On |
| D1502 | Telehandler | Brake Light Relay Error On |
| D1503 | Telehandler | Trailer Brake Command Line Relay Error Off |
| D1503 | Telehandler | Brake Light Relay Error Off |
| D1605 | Telehandler | Drive Pump Forward Coil Short To Battery |
| D1606 | Telehandler | Drive Pump Forward Coil Short To Ground |
| D1607 | Telehandler | Drive Pump Forward Coil Open circuit |
| D1632 | Telehandler | Drive Pump Forward Coil Overcurrent |
| D1705 | Telehandler | Drive Pump Reverse Coil Short To Battery |
| D1706 | Telehandler | Drive Pump Reverse Coil Short To Ground |
| D1707 | Telehandler | Drive Pump Reverse Coil Open circuit |
| D1732 | Telehandler | Drive Pump Reverse Coil Overcurrent |
| D1802 | Telehandler | Stabilisers / Aux diverter output valve error ON |
| D1803 | Telehandler | Stabilisers / Aux diverter output valve error OFF |
| D1807 | Telehandler | Stabilisers / Aux diverter output open circuit |
| D1825 | Telehandler | Stabilisers / Aux diverter output Unresponsive |
| D1902 | Telehandler | Stabilisers / Aux diverter relay feedback error ON |
| D1903 | Telehandler | Stabilisers / Aux diverter relay feedback error OFF |
| D2002 | Telehandler | Low speed output (hydraulic motor) Error On |
| D2003 | Telehandler | Low speed output (hydraulic motor) Error Off |
| D2007 | Telehandler | Low speed output (hydraulic motor) Open circuit |
| D2033 | Telehandler | Low speed output (hydraulic motor) Controller Internal failure |
| D2102 | Telehandler | Low speed Relay Error On |
| D2103 | Telehandler | Low speed Relay Error Off |
| D2202 | Telehandler | Defeat valve output (hydraulic motor) Error On |
| D2203 | Telehandler | Defeat valve output (hydraulic motor) Error Off |
| D2207 | Telehandler | Defeat valve output (hydraulic motor) Open circuit |
| D2233 | Telehandler | Defeat valve output Controller Internal failure |
| D2302 | Telehandler | Defeat valve relay Error On |
| D2303 | Telehandler | Defeat valve relay Error Off |
| D2502 | Telehandler | Left stabilizer on the floor Error ON |
| D2503 | Telehandler | Left stabilizer on the floor Error OFF |
| D2609 | Telehandler | Hydraulic Steering Pressure Low |
| D2621 | Telehandler | Hydraulic Steering Pressure Out of Range High |
| D2702 | Telehandler | Right stabilizer on the floor Error ON |
| D2703 | Telehandler | Right stabilizer on the floor Error OFF |
| D2821 | Telehandler | Left stabilizer Pressure Sensor Out Of Range High |
| D2822 | Telehandler | Left stabilizer Pressure Sensor Out Of Range Low |
| D2921 | Telehandler | Right stabilizer Pressure Sensor Out Of Range High |
| D2922 | Telehandler | Right stabilizer Pressure Sensor Out Of Range Low |
| D3005 | Telehandler | Stabilizers Right Output Short To Battery |
| D3006 | Telehandler | Stabilizers Right Output Short To Ground |
| D3007 | Telehandler | Stabilizers Right Output Open circuit |
| D3024 | Telehandler | Stabilizers Right Output Not In Neutral |
| D3105 | Telehandler | Stabilizers Left Output Short To Battery |
| D3106 | Telehandler | Stabilizers Left Output Short To Ground |
| D3107 | Telehandler | Stabilizers Left Output Open circuit |
| D3124 | Telehandler | Stabilizers Left Output Not In Neutral |
| D3204 | Telehandler | Workgroup controller No Communication |
| D3304 | Telehandler | Gateway controller No Communication |
| D3404 | Telehandler | Display controller No Communication |
| D3604 | Telehandler | Engine controller No Communication |
| D3723 | Telehandler | Programming or constant data invalid |
| D3728 | Telehandler | Drive Controller failure |
| D3796 | Telehandler | Interrupted power |
| D3797 | Telehandler | Drive Controller programmed |
| D3905 | M-Series Loader | Left Joystick X-Axis Not in Neutral |
| D3907 | M-Series Loader | Left Joystick Y-Axis Not in Neutral |
| D4004 | Telehandler | Joystick No communication |
| D4007 | M-Series Loader | Right Joystick Y-Axis Not in Neutral |
| D4011 | Telehandler | Joystick Right roller Out Of Neutral (Auxiliary) |
| D4028 | Telehandler | Joystick Grip Fault |
| D4113 | Telehandler | FNR lever no Signal |
| D4128 | Telehandler | FNR multiple inputs active |
| D4402 | Telehandler | Power Quicktach output Error On |
| D4403 | Telehandler | Power Quicktach output Error Off |
| D4407 | Telehandler | Power Quicktach Output Open circuit |
| D4502 | Telehandler | Power Quicktach Relay feedback Error On |
| D4503 | Telehandler | Power Quicktach Relay feedback Error Off |
| D4528 | Telehandler | Power Quicktach Switch in error |
| D4621 | Telehandler | Voltage Sensor 5V OOR High |
| D4622 | Telehandler | Voltage Sensor 5V OOR Low |
| D4705 | Telehandler | Frame leveling Output Short To Battery |
| D4706 | Telehandler | Frame leveling Output Short To Ground |
| D4707 | Telehandler | Frame leveling Output Open circuit |
| D4724 | Telehandler | Frame leveling Output Not In Neutral |
| D4802 | Telehandler | Park Brake Reserve Pressure Valve Output Error On |
| D4803 | Telehandler | Park Brake Reserve Pressure Valve Output Error Off |
| D4807 | Telehandler | Park Brake Reserve Pressure Valve Output Open Circuit |
| D4902 | Telehandler | Park Brake Reserve Pressure Valve Relay Feedback Error On |
| D4903 | Telehandler | Park Brake Reserve Pressure Valve Relay Feedback Error Off |
| D5005 | Telehandler | Rear Aux./Hook UP Valve Short to Battery |
| D5006 | Telehandler | Rear Aux./Hook UP Valve Short to Ground |
| D5007 | Telehandler | Rear Aux./Hook UP Valve Open Circuit |
| D5105 | Telehandler | Rear Aux./Hook DOWN Valve Short to Battery |
| D5106 | Telehandler | Rear Aux./Hook DOWN Valve Short to Ground |
| D5107 | Telehandler | Rear Aux./Hook DOWN Valve Open Circuit |
| D5205 | Telehandler | Rear Aux./Hook ACTIVATION Valve Short to Battery |
| D5206 | Telehandler | Rear Aux./Hook ACTIVATION Valve Short to Ground |
| D5207 | Telehandler | Rear Aux./Hook ACTIVATION Valve Open Circuit |
| D5232 | Telehandler | Rear Aux./Hook ACTIVATION Valve Overcurrent |
| D5328 | Telehandler | Rear Aux./Hook Dashbord Switch In Error |
| D5421 | Telehandler | Auxiliary spool sensor Out Of Range high |
| D5422 | Telehandler | Auxiliary spool sensor Out Of Range low |
| D5424 | Telehandler | Auxiliary spool sensor not in neutral |
| D5425 | Telehandler | Auxiliary spool sensor unresponsive |
| D5521 | Telehandler | SwashPlate Sensor1 OORH |
| D5522 | Telehandler | SwashPlate Sensor1 OORL |
| D5621 | Telehandler | Swash Plate Sensor2 OORH |
| D5622 | Telehandler | Swash Plate Sensor2 OORL |
| D5715 | Telehandler | Swash Plate shutdown |
| D5744 | Telehandler | Swash Plate dual fault |
| D5745 | Telehandler | Swash Plate disagree |
| D5746 | Telehandler | Swash plate unresponsive |
| D5786 | Telehandler | Swash plate Safe Stop failure |
| D5815 | Telehandler | Safe Start Shutdown |
| D5824 | Telehandler | Safe Start Swash Out Of Neutral |
| D5835 | Telehandler | Safe Start Dump valve stuck on |
| D5911 | Telehandler | Overspeed fault |
| D5915 | Telehandler | Overspeed shutdown |
| D5928 | Telehandler | Overspeed failure |
| D5986 | Telehandler | Overspeed failure |
| D6021 | Telehandler | Servo Pressure Out of Range High |
| D6022 | Telehandler | Servo Pressure Out of Range Low |
| D6202 | Telehandler | Creep Light Error On |
| D6203 | Telehandler | Creep Light Error Off |
| D6302 | Telehandler | Creep Switch Error On |
| D6505 | Telehandler | Gear 1 (Gearbox) Short To Battery |
| D6506 | Telehandler | Gear 1 (Gearbox) Short To Ground |
| D6507 | Telehandler | Gear 1 (Gearbox) Open Circuit |
| D6605 | Telehandler | Gear 2 (Gearbox) Short To Battery |
| D6606 | Telehandler | Gear 2 (Gearbox) Short To Ground |
| D6607 | Telehandler | Gear 2 (Gearbox) Open Circuit |
| D6702 | Telehandler | Gearshift sensor Error On |
| D6760 | Telehandler | Gearshift sensor – Shift didn’t start / no shift |
| D6761 | Telehandler | Gearshift sensor – Shift too long / locked |
| D6824 | Telehandler | Frame leveling switch Not in Neutral |
| D6902 | Telehandler | Gear switch 1/2 Error On (dashboard) |
| D7002 | Telehandler | High/Low speed switch Error on (left lever) |
| D7102 | Telehandler | Backup alarm Output Error On |
| D7103 | Telehandler | Backup alarm Output Error Off |
| D7107 | Telehandler | Backup alarm Output Open Cirduit |
| D7133 | Telehandler | Backup alarm Output Internal Failure |
| D7202 | Telehandler | Backup alarm Relay Feedback Error On |
| D7203 | Telehandler | Backup alarm Relay Feedback Error Off |
| D7209 | Telehandler | Service Brake Pressure Low |
| D7210 | Telehandler | Service Brake Pressure High |
| D7214 | Telehandler | Service Brake Pressure Extremley Low |
| D7221 | Telehandler | Service Brake Pressure Out of Range High |
| D7222 | Telehandler | Service Brake Pressure Out of Range Low |
| D7309 | Telehandler | Service Brake Reserve Pressure Low |
| D7310 | Telehandler | Service Brake Reserve Pressure High |
| D7321 | Telehandler | Service Brake Reserve Pressure Out of Range High |
| D7322 | Telehandler | Service Brake Reserve Pressure Out of Range Low |
| D7501 | M-Series Loader | Drive/Drive+ CAN Joystick Information Error |
| D7502 | M-Series Loader | Drive Controller Needs Programming |
| D7504 | M-Series Loader | Drive No Communication from Drive Controller |
| D7505 | M-Series Loader | Drive Left Joystick X-Axis Not in Neutral |
| D7506 | M-Series Loader | Drive+ Steering valve cartridge stuck |
| D7507 | M-Series Loader | Drive Left Joystick Y-Axis Not in Neutral |
| D7508 | M-Series Loader | Drive Right Joystick Y-Axis Not in Neutral |
| D7509 | M-Series Loader | Drive ISO/H Pattern Switch Short to Ground or Battery |
| D7509 | Telehandler | Park Brake Reserve Pressure Low |
| D7510 | M-Series Loader | Drive Improper Joysticks installed |
| D7511 | M-Series Loader | Drive Left speed sensor not connected. |
| D7512 | M-Series Loader | Drive Right speed sensor not connected |
| D7513 | M-Series Loader | Drive+ Right Front Wheel Angle Sensor Stuck |
| D7514 | M-Series Loader | Drive+ Left Front Wheel Angle Sensor Stuck |
| D7515 | M-Series Loader | Drive+ Right Reat Wheel Angle Sensor Stuck |
| D7516 | M-Series Loader | Drive+ Left Rear Wheel Angle Sensor Stuck |
| D7517 | M-Series Loader | Drive Left Swash Plate Not in Neutral |
| D7518 | M-Series Loader | Drive Right Swash Plate Not in Neutral |
| D7519 | M-Series Loader | Drive Left Joystick X-Axis Out of Range High |
| D7521 | M-Series Loader | Drive Left Joystick Y-Axis Out of Range High |
| D7522 | M-Series Loader | Drive Right Joystick Y-Axis Out of Range High |
| D7523 | M-Series Loader | Drive+ Right Front Wheel Angle Sensor Out of Range High |
| D7524 | M-Series Loader | Drive+ Left Front Wheel Angle Sensor Out of Rane High |
| D7525 | M-Series Loader | Drive+ Right Rear Wheel Angle Sensor Out of Range High |
| D7526 | M-Series Loader | Drive+ Left Rear Wheel Angle Sensor Out of Range High |
| D7527 | M-Series Loader | Drive Left Swash Plate Out of Position |
| D7528 | M-Series Loader | Drive Right Swash Plate Out of Position |
| D7529 | M-Series Loader | Drive Left Joystick X-Axis Out of Range Low |
| D7531 | M-Series Loader | Drive Left Joystick Y-Axis Out of Range Low |
| D7532 | M-Series Loader | Drive Right Joystick Y-Axis Out of Range Low |
| D7533 | M-Series Loader | Drive+ Right Front Wheel Angle Sensor Out of Range Low |
| D7534 | M-Series Loader | Drive+ Left Front Wheel Angle Sensor Out of Range Low |
| D7535 | M-Series Loader | Drive+ Right Rear Wheel Angle Sensor Out of Range Low |
| D7536 | M-Series Loader | Drive+ Left Rear Wheel Angle Sensor Out of Range Low |
| D7537 | M-Series Loader | Drive 5 Volt Sensor Supply 1 Out of Range Low |
| D7538 | M-Series Loader | Drive+ Sensor Supply 2 Out of Range Low |
| D7539 | M-Series Loader | Drive Left Swash Plate Sensor Out of Range High |
| D7540 | M-Series Loader | Drive Left Swash Plate Sensor Out of Range Low |
| D7541 | M-Series Loader | Drive Right Swash Plate Sensor Out of Range High |
| D7542 | M-Series Loader | Drive Right Swash Plate Sensor Out of Range Low |
| D7543 | M-Series Loader | Drive Left Forward Drive Solenoid Error On |
| D7544 | M-Series Loader | Drive Left Reverse Drive Solenoid Error On |
| D7545 | M-Series Loader | Drive Right Forward Drive Solenoid Error On |
Bobcat Fault Code List T770
| Bobcat Fault Code | Product | Description |
| B1005-00 | Compact Wheel Loader | Key Switch Multiple |
| B1034-11 | Compact Wheel Loader | Rear Work Light Short to Battery |
| B1034-12 | Compact Wheel Loader | Rear Work Light Short to Ground |
| B1034-13 | Compact Wheel Loader | Rear Work Light Not Connected |
| B1037-11 | Compact Wheel Loader | Stop Light Short to Ground |
| B1037-15 | Compact Wheel Loader | Stop Light Error On |
| B103D-11 | Compact Wheel Loader | Beacon Short to Ground |
| B103D-12 | Compact Wheel Loader | Beacon Short to Battery |
| B103D-13 | Compact Wheel Loader | Beacon Not Connected |
| B1040-11 | Compact Wheel Loader | Buzzer Error Off |
| B1040-12 | Compact Wheel Loader | Buzzer Error On |
| B1041-12 | Compact Wheel Loader | Backup Alarm Error Off |
| B1041-14 | Compact Wheel Loader | Backup Alarm Error On |
| B104A-11 | Compact Wheel Loader | Seat Heater Short to Ground |
| B104A-12 | Compact Wheel Loader | Seat Heater Short to Battery |
| B104A-13 | Compact Wheel Loader | Seat Heater Open Circuit |
| B1064-F0 | Compact Wheel Loader | Lift Input Not in Neutral |
| B1074-F0 | Compact Wheel Loader | Tilt Input Not in Neutral |
| B1080-09 | Compact Wheel Loader | Operator Presence Component Failure |
| B1080-16 | Compact Wheel Loader | Operator Presence Circuit Voltage Below Threshold |
| B1080-17 | Compact Wheel Loader | Operator Presence Circuit Voltage Above Threshold |
| B10A2-11 | Compact Wheel Loader | Front Wiper Short to Ground |
| B10A2-12 | Compact Wheel Loader | Front Wiper Short to Battery |
| B10A2-13 | Compact Wheel Loader | Front Wiper Not connected |
| B10A3-11 | Compact Wheel Loader | Front Wiper High Speed Short to Ground |
| B10A3-12 | Compact Wheel Loader | Front Wiper High Speed Short to Battery |
| B10A3-13 | Compact Wheel Loader | Front Wiper High Speed Not connected |
| B10A5-11 | Compact Wheel Loader | Rear Wiper Short to Ground |
| B10A5-12 | Compact Wheel Loader | Rear Wiper Short to Battery |
| B10A5-13 | Compact Wheel Loader | Rear Wiper Not Connected |
| B10A7-11 | Compact Wheel Loader | Front Washer Short to Ground |
| B10A7-12 | Compact Wheel Loader | Front Washer Short to Battery |
| B10A7-13 | Compact Wheel Loader | Front Washer Not Connected |
| B10A8-11 | Compact Wheel Loader | Rear Washer Short to Ground |
| B10A8-12 | Compact Wheel Loader | Rear Washer Short to Battery |
| B10A8-13 | Compact Wheel Loader | Rear Washer Not Connected |
| B10C0-00 | Compact Wheel Loader | Camera Not Connected |
| B10F0-11 | Compact Wheel Loader | Rear Defog Short to Ground |
| B10F0-12 | Compact Wheel Loader | Rear Defog Short to Battery |
| B10F0-13 | Compact Wheel Loader | Rear Defog Circuit Open |
| B1100-9E | Compact Wheel Loader | Power Exchange Lock Switch Stuck On |
| B1101-9E | Compact Wheel Loader | Power Exchange Unlock Switch Stuck on |
| B1120-F0 | Compact Wheel Loader | Joystick Right Roller Not in Neutral |
| B1150-F0 | Compact Wheel Loader | FNR Lever not in Neutral |
| B1151-00 | Compact Wheel Loader | FNR Switch Multiple |
| B1190-11 | Compact Wheel Loader | Front Work Light Short to Battery |
| B1190-12 | Compact Wheel Loader | Front Work Light Short to Ground |
| B1190-13 | Compact Wheel Loader | Front Work Light Not Connected |
| B11B5-54 | Compact Wheel Loader | Inching pedal sensor mising calibration |
| C1001-16 | Compact Wheel Loader | Sensor Supply Out of Range Low |
| C1001-17 | Compact Wheel Loader | Sensor Supply Out of Range High |
| C1003-16 | Compact Wheel Loader | Sensor Supply Out of Range Low |
| C1003-17 | Compact Wheel Loader | Sensor Supply Out of Range High |
| C1004-16 | Compact Wheel Loader | Drive Controller Sensor Supply Out of Range Low |
| C1004-17 | Compact Wheel Loader | Drive Controller Sensor Supply Out of Range High |
| C101A-16 | Compact Wheel Loader | Lift Base Pressure Out of Range Low |
| C101A-17 | Compact Wheel Loader | Lift Base Pressure Out of Range High |
| C1020-11 | Compact Wheel Loader | Front Base Solenoid Short to Ground |
| C1020-12 | Compact Wheel Loader | Front Base Solenoid Short to Battery |
| C1020-13 | Compact Wheel Loader | Front Base Solenoid Open Circuit |
| C1020-19 | Compact Wheel Loader | Front Base Solenoid Overcurrent |
| C1021-11 | Compact Wheel Loader | Front Rod Solenoid Short to Ground |
| C1021-12 | Compact Wheel Loader | Front Rod Solenoid Short to Battery |
| C1021-13 | Compact Wheel Loader | Front Rod Solenoid Open Circuit |
| C1021-19 | Compact Wheel Loader | Front Rod Solenoid Overcurrent |
| C102A-11 | Compact Wheel Loader | Hydraulic Fan Short to Ground |
| C102A-12 | Compact Wheel Loader | Hydraulic Fan Short to Battery |
| C102A-13 | Compact Wheel Loader | Hydraulic Cooling Fan Electrical Problem |
| C102A-19 | Compact Wheel Loader | Hydraulic Fan Overcurrent |
| C1039-11 | Compact Wheel Loader | High Flow Solenoid Short to Ground |
| C1039-12 | Compact Wheel Loader | High Flow Solenoid Short to Battery |
| C1039-13 | Compact Wheel Loader | High Flow Solenoid Open Circuit |
| C1043-11 | Compact Wheel Loader | Lift Cylinder Base Short to Ground |
| C1043-12 | Compact Wheel Loader | Lift Cylinder Base Short to Battery |
| C1043-13 | Compact Wheel Loader | Lift Cylinder Base Open Circuit |
| C1043-19 | Compact Wheel Loader | Lift Cylinder Base Overcurrent |
| C1044-11 | Compact Wheel Loader | Lift Cylinder Rod Short to Ground |
| C1044-12 | Compact Wheel Loader | Lift Cylinder Rod Short to Battery |
| C1044-13 | Compact Wheel Loader | Lift Cylinder Rod Open Circuit |
| C1044-19 | Compact Wheel Loader | Lift Cylinder Rod Overcurrent |
| C1048-11 | Compact Wheel Loader | Tilt Cylinder Rod Short to Ground |
| C1048-12 | Compact Wheel Loader | Tilt Cylinder Rod Short to Battery |
| C1048-13 | Compact Wheel Loader | Tilt Cylinder Rod Open Circuit |
| C1048-19 | Compact Wheel Loader | Tilt Cylinder Rod Overcurrent |
| C1049-11 | Compact Wheel Loader | Tilt Cylinder Base Short to Ground |
| C1049-12 | Compact Wheel Loader | Tilt Cylinder Base Short to Battery |
| C1049-13 | Compact Wheel Loader | Tilt Cylinder Base Open Circuit |
| C1049-19 | Compact Wheel Loader | Tilt Cylinder Base Overcurrent |
| C1050-11 | Compact Wheel Loader | Switched Power Relay Short to Ground |
| C1050-12 | Compact Wheel Loader | Switched Power Relay Short to Battery |
| C1050-13 | Compact Wheel Loader | Switched Power Relay Open Circuit |
| C1060-11 | Compact Wheel Loader | Brake Short to Ground |
| C1060-12 | Compact Wheel Loader | Brake Short to Battery |
| C1060-13 | Compact Wheel Loader | Brake Open Circuit |
| C1060-19 | Compact Wheel Loader | Brake Solenoid Overcurrent |
| C1090-00 | Compact Wheel Loader | Hydraulic Filter Plugged |
| C1091-95 | Compact Wheel Loader | Hydraulic Main Filter Switch Not Connected |
| C1099-FA | Compact Wheel Loader | Hydraulic Oil Temperature Too High |
| C1099-FB | Compact Wheel Loader | Hydraulic Oil Temperature Extremely High |
| C1099-FC | Compact Wheel Loader | Hydraulic Oil Temperature Performance Reduction |
| C109A-16 | Compact Wheel Loader | Hydraulic Oil Temperature Out of Range Low |
| C109A-17 | Compact Wheel Loader | Hydraulic Oil Temperature Out of Range High |
| C10D1-11 | Compact Wheel Loader | Drive Pump Forward Short to Ground |
| C10D1-12 | Compact Wheel Loader | Drive Pump Forward Short to Battery |
| C10D1-13 | Compact Wheel Loader | Drive Pump Forward Open Circuit |
| C10D1-19 | Compact Wheel Loader | Drive Pump Forward Overcurrent |
| C10D2-11 | Compact Wheel Loader | Drive Pump reverse Short to Ground |
| C10D2-12 | Compact Wheel Loader | Drive Pump reverse Short to Battery |
| C10D2-13 | Compact Wheel Loader | Drive Pump reverse Open Circuit |
| C10D2-19 | Compact Wheel Loader | Drive Pump reverse Overcurrent |
| C1110-11 | Compact Wheel Loader | Ride Control Circuit Short to Ground |
| C1110-15 | Compact Wheel Loader | Ride Control Circuit Error On |
| C1111-16 | Compact Wheel Loader | Ride Control Feedback Circuit Out of Range Low |
| C1111-17 | Compact Wheel Loader | Ride Control Feedback Circuit Out of Range High |
| C1130-11 | Compact Wheel Loader | Hydraulic Motor reverse Short to Ground |
| C1130-12 | Compact Wheel Loader | Hydraulic Motor reverse Short to Battery |
| C1130-13 | Compact Wheel Loader | Hydraulic Motor reverse Open Circuit |
| C1130-19 | Compact Wheel Loader | Hydraulic Motor Overcurrent |
| C1182-A2 | Compact Wheel Loader | Alternator Voltage Low |
| C1183-A3 | Compact Wheel Loader | Alternator Voltage High |
| C1192-00 | Compact Wheel Loader | System Voltage Extremely Low |
| C1193-00 | Compact Wheel Loader | System Voltage Too Low |
| C1195-00 | Compact Wheel Loader | System Voltage High |
| C1196-00 | Compact Wheel Loader | System Voltage Extremely High |
| C1200-11 | Compact Wheel Loader | Power Exchange Unlock Short to Ground |
| C1200-12 | Compact Wheel Loader | Power Exchange Unlock Short to Battery |
| C1200-13 | Compact Wheel Loader | Power Exchange Unlock Open Circuit |
| C1205-11 | Compact Wheel Loader | Power Exchange Lock Short to Ground |
| C1205-12 | Compact Wheel Loader | Power Exchange Lock Short to Battery |
| C1205-13 | Compact Wheel Loader | Power Exchange Lock Open Circuit |
| C1220-11 | Compact Wheel Loader | Diff-Lock Short to Ground |
| C1220-12 | Compact Wheel Loader | Diff-Lock Short to Battery |
| C1220-13 | Compact Wheel Loader | Diff-Lock Open Circuit |
| C1220-19 | Compact Wheel Loader | Diff-Lock Overcurrent |
| C1221-17 | Compact Wheel Loader | Diff-Lock Sensor Out of Range High |
| C1250-F9 | Compact Wheel Loader | Park Brake Pressure Low |
| C1250-FA | Compact Wheel Loader | Park Brake Pressure High |
| C1251-16 | Compact Wheel Loader | Park Brake Pressure Sensor Circuit Out of Range Low |
| C1251-17 | Compact Wheel Loader | Park Brake Pressure Sensor Circuit Out of Range High |
| C1260-F9 | Compact Wheel Loader | Service Brake Pressure Low |
| C1260-FA | Compact Wheel Loader | Service Brake Pressure High |
| C1260-FB | Compact Wheel Loader | Service Brake Pressure Extremely High |
| C1261-16 | Compact Wheel Loader | Service Brake Pressure Sensor Circuit Out of Range Low |
| C1261-17 | Compact Wheel Loader | Service Brake Pressure Sensor Circuit Out of Range High |
| C1270-F9 | Compact Wheel Loader | Steering Pressure Low |
| C1271-16 | Compact Wheel Loader | Steering Pressure Sensor Circuit Out of Range Low |
| C1271-17 | Compact Wheel Loader | Steering Pressure Sensor Circuit Out of Range High |
| C1280-F9 | Compact Wheel Loader | Reserve Brake Pressure Low |
| C1280-FA | Compact Wheel Loader | Reserve Brake Pressure High |
| C1280-FB | Compact Wheel Loader | Reserve Brake Pressure Extremely Low |
| C1281-16 | Compact Wheel Loader | Reserve Brake Pressure Sensor Circuit Out of Range Low |
| C1281-17 | Compact Wheel Loader | Reserve Brake Pressure Sensor Circuit Out of Range High |
| C12F0-FB | Compact Wheel Loader | Hydromotor Speed Extremely High |
| C12F1-31 | Compact Wheel Loader | Hydromotor Speed Sensor Not Connected |
| C1300-16 | Compact Wheel Loader | Inching Sensor Circuit Out of Range Low |
| C1300-17 | Compact Wheel Loader | Inching Sensor Circuit Out of Range High |
| P0225-16 | Compact Wheel Loader | Throttle Pedal Sensor Out of Range Low |
| P0225-17 | Compact Wheel Loader | Throttle Pedal Sensor Out of Range High |
| P0226-16 | Compact Wheel Loader | Throttle Pedal Sensor Secondary Out of Range Low |
| P0226-17 | Compact Wheel Loader | Throttle Pedal Sensor Secondary Out of Range High |
| P0227-93 | Compact Wheel Loader | Throttle Pedal Failure |
| P0460-16 | Compact Wheel Loader | Fuel Level Sensor Out of Range Low |
| P0460-17 | Compact Wheel Loader | Fuel Level Sensor Problem |
| P1061-97 | Compact Wheel Loader | Air Filter Plugged |
| P1065-31 | Compact Wheel Loader | Air Filter Switch Not Connected |
| P1100-FA | Compact Wheel Loader | Engine Coolant Temperature High |
| P1100-FB | Compact Wheel Loader | Engine Coolant Temperature Extremely High |
| P1100-FC | Compact Wheel Loader | Engine Coolant Temperature Shutdown |
| P1110-FA | Compact Wheel Loader | Fuel Temperature High |
| P1110-FB | Compact Wheel Loader | Fuel Temperature Extremely High |
| P1110-FC | Compact Wheel Loader | Fuel Temperature Limiting Performance |
| P1115-FA | Compact Wheel Loader | Air Intake Temperature Too High |
| P1115-FB | Compact Wheel Loader | Air Intake Temperature Extremely High |
| P1115-FC | Compact Wheel Loader | Air Intake Temperature Limiting Performance |
| P1120-00 | Compact Wheel Loader | Fuel Filter Plugged |
| P1121-00 | Compact Wheel Loader | Fuel Filter Derate Level 1 |
| P1122-00 | Compact Wheel Loader | Fuel Filter Derate Level 2 |
| P1125-00 | Compact Wheel Loader | Fuel Filter Extremely Plugged |
| P1130-F8 | Compact Wheel Loader | Fuel Filter Inlet Pressure Extremely Low |
| P1130-F9 | Compact Wheel Loader | Fuel Filter Inlet Pressure Low |
| P1131-16 | Compact Wheel Loader | Fuel Pressure Out of Range Low |
| P1131-17 | Compact Wheel Loader | Fuel Pressure Out of Range High |
| P1134-11 | Compact Wheel Loader | Fuel Lift Pump Short to Ground |
| P1134-15 | Compact Wheel Loader | Fuel Lift Pump Short Error On |
| P1134-63 | Compact Wheel Loader | Fuel Lift Pump Protection Time-Out |
| P113B-7B | Compact Wheel Loader | Fuel Level Low |
| U1010-08 | Compact Wheel Loader | PTOL Keypad No Communication |
| U1012-08 | Compact Wheel Loader | Cab Keypad No Communication |
| U1013-08 | Compact Wheel Loader | Accessory (ACD) Keypad No Communication |
| U1040-00 | Compact Wheel Loader | Hour Meter Changed |
| U1050-00 | Compact Wheel Loader | Power Failure |
| U1053-00 | Compact Wheel Loader | Drive Controller Interrupted Power |
| U1054-00 | Compact Wheel Loader | Interrupted Power Failure |
| U1070-00 | Compact Wheel Loader | Hub Controller Software Updated |
| U1073-00 | Compact Wheel Loader | Drive Controller Programmed |
| U1074-00 | Compact Wheel Loader | Workgroup Controller Software Updated |
| U1090-51 | Compact Wheel Loader | Hub Controller Not Programmed |
| U1090-57 | Compact Wheel Loader | Hub Controller Software Version Error |
| U1091-08 | Compact Wheel Loader | Display No Communication |
| U1091-51 | Compact Wheel Loader | Display Not Programmed |
| U1091-FD | Compact Wheel Loader | Display Shutdown |
| U1094-08 | Compact Wheel Loader | Drive Controller No Communication |
| U1094-51 | Compact Wheel Loader | Drive Controller Not Progammed |
| U1094-57 | Compact Wheel Loader | Drive Controller Software Update Required |
| U1094-A2 | Compact Wheel Loader | Drive Controller Voltage Out of Range Low |
| U1094-A3 | Compact Wheel Loader | Drive Controller Voltage Out of Range High |
| U1095-08 | Compact Wheel Loader | Workgroup Controller No Communication |
| U1095-51 | Compact Wheel Loader | Workgroup Controller Not Programmed |
| U1095-57 | Compact Wheel Loader | Workgroup Controller Software Version Error |
| U1095-A2 | Compact Wheel Loader | Workgroup Controller System Voltage Low |
| U1095-A3 | Compact Wheel Loader | Workgroup Controller System Voltage High |
| U1096-08 | Compact Wheel Loader | ECU No Communication |
| U1096-56 | Compact Wheel Loader | ECU Failure |
| U10C0-08 | Compact Wheel Loader | Right Joystick Base Message Failure |
| U1180-00 | Compact Wheel Loader | Display Controller Communcation Error |
| U1181-00 | Compact Wheel Loader | Display Controller Communcation Error |
| U1182-00 | Compact Wheel Loader | Display Controller Communcation Error |
| U1183-00 | Compact Wheel Loader | Main Controller No Communication |
| U1184-00 | Compact Wheel Loader | Jog Shuttle No Communication |
How to Retrieve Bobcat Engine Codes?
To retrieve the engine codes from a Bobcat machine, follow these general steps:
- Find the Diagnostic Connector: Look for a special plug on your Bobcat machine, usually near where the driver sits or under the front part of the machine. It looks like a rectangle with pins inside.
- Get Ready: Make sure the machine is turned off, the key is out, and the parking brake is on to stay safe.
- Use a Diagnostic Tool: Get a special tool that can talk to the machine’s engine computer. Connect this tool to the plug you found earlier.
- Turn On the Key: Turn the key to the “On” position (but don’t start the engine). The diagnostic tool will turn on and talk to the machine’s computer.
- Check for Codes: The diagnostic tool will show different numbers on the screen. These numbers are like secret messages that tell us if there are any problems with the engine.
- Write Down the Numbers: Take note of the numbers you see on the screen. Each number means something is not working right.
- Understand the Numbers: Look up these numbers in a special book or chart. It will tell you what each number means and why it’s happening.
- Fix the Problems: Based on what the numbers say, you can try to fix the problems. Some issues might be easy to fix, while others may need help from a mechanic.
Bobcat Fault Codes List Printable PDF
The Bottom Line
Thanks for waiting. We’ve discussed all the important problems with Bobcat tractors.
Remember, always follow the instructions from the maker when trying to fix problems by yourself.
If you have trouble figuring things out, go to the nearest Bobcat service center or ask a qualified expert for help. They know how to find and solve the issues correctly.
